Windows 10: Network connections disabled after running command prompt!

Hello, I was trying to fix the windows installation error 0x80070017 and i came across this video:https://youtu.be/gPiCdY08e6wIn his guide, he uses these command prompts in order to solve it:SC config trustedinstaller start=autonet stop wauaservnet stop msiservernet stop cryptsvcnet stop appidsvcRen %Systemroot%\SoftwareDistribution SoftwareDistribution.oldRen %Systemroot%\System32\catroot.oldregvr32.exe /s atl.dllregvr32.exe /s urlmon.dllregvr32.exe /s mshtml.dllnetsh winsock resetnetsh winsock reset proxyrundll32.exe pnpclean.dll,RunDLL_PnpClean /DRIVERS /MAXCLEANnet stop wauaservnet stop ms

:)

 

command prompt will not open in safe mode with command prompt

Would I just follow the same steps within safe mode after hooking up to the other system?

 

Text Services Framework not running and no connection to Internet

Hi Alrescha,

It is possible that the
system files
and
components were corrupted during the installation or update. We suggest
that you perform these methods of troubleshooting
and check if there are any
changes:

For network connection issue:

Method 1: Reset TCP/IP

To do this, follow these steps:

• 
  Run
  Command Prompt
  as
  Administrator.
  
• 
  Run
  this command:
  
  • 
    netsh int ip reset
    and hit
    Enter.
    

Exit
Command Prompt
and
monitor your Network Connection.

Method 2: Disable auto turn-off of Network device.

Go to
Network and Sharing Center. At the
right pane, click
Change adapter settings.
Right-click
on your
connection/network name
and go to
Properties.Click
the
"Configure..."
button and go to
Power Management
tab.Uncheck/disable
the
radio button
for
"Allow this device to turn off this device to save power". And then,
Restart the PC(Important).

Method 3: Reconfigure TCP/IP

To do this, follow these steps:

• 
  Run
  Command Prompt
  as
  Administrator.
  
• 
  Run
  these following commands:
  
  • 
    netsh int tcp set heuristics
    disabled
    
  • 
    netsh int tcp
    set global autotuninglevel=disabled
    
  • 
    netsh int tcp set global
    rss=enabled
    

For keyboard issue:

Method 1:
Run SFC Scan.  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Note:
Kindly run
SFC twice or thrice and check for results before you proceed to the next method.

Method 2: Reset Windows Update Components.

Resetting your
Windows Update Components
will allow you to
install
the update again including the
Text Services Framework. To do this, refer to
How do I reset Windows Update Components.

 

Set Broadband Internet Connection Network Configuration

Hi,

Upon analyzing the details you have provided, kindly run the
Network and Internet Troubleshooter
and check if there's any changes. To run the
troubleshooter,
follow these steps:

• 
  On the search bar, type
  Troubleshooting.
  
• 
  Choose
  Network and Internet.
  
• 
  Run the following
  Troubleshooter:
  
  • 
    Internet Connections.
    
  • 
    Network Adapter.
    
  • 
    Incoming Connections.
    

If the issue persists, we suggest that you try to
renew
your
IP address. To do this, follow these steps:

• 
  Open
  Command Prompt
  as
  Administrator.
  
• 
  Type the following command:
  
  • 
    Ipconfig/release
    and hit
    Enter.
    
  • 
    Ipconfig/renew
    and hit
    Enter.
    
  • 
    Exit.
    

Let us know how it goes.

Regards.