Windows 10: Network services are not running

I have a Dell laptop running Windows 11. My laptop can’t connect to wifi because the network services have stopped. I have tried uninstalling the network adapter driver and restarting and updating the adapter driver. My WLAN AutoConfig is not running and every time I try to start it I receive Error 126: The specified module could not be found. I have also tried uninstalling the latest quality update, without success. Any help would be greatly appreciated!!

:)

 

Windows wireless service is not running on this computer?

Hi,



Thank you for updating us. It must be unfortunate that you are still facing the same issue. Let me help you.



I suggest you to perform below mentioned troubleshooting steps and check if it helps.

Method 1: Run the Network Adapter troubleshooter.

Follow the below steps:

• 
  Type troubleshooting in the search bar.
  
• 
  Select Troubleshooting.
  
• 
  Select View all on the top left corner.
  
• 
  Click on Network Adapter.
  
• 
  Follow the on-screen instructions to run the troubleshooter.
  

If the issue persists then follow the below method.

Method 2: Update driver manually.

I suggest you to update the Network Adapter from the Device Manager.

Follow the below steps:

• 
  Right click on Start button and click on Device Manager.
  
• 
  Extend Network adapters driver from the list.
  
• 
  Right click on the Network driver and click on
  Update driver Software.
  

Check if it helps to resolve the issue.



I hope the information helps. Please keep us posted on the issue. We will be happy to assist you accordingly.

Thank you.

 

Text Services Framework not running and no connection to Internet

Hi Alrescha,

It is possible that the
system files
and
components were corrupted during the installation or update. We suggest
that you perform these methods of troubleshooting
and check if there are any
changes:

For network connection issue:

Method 1: Reset TCP/IP

To do this, follow these steps:

• 
  Run
  Command Prompt
  as
  Administrator.
  
• 
  Run
  this command:
  
  • 
    netsh int ip reset
    and hit
    Enter.
    

Exit
Command Prompt
and
monitor your Network Connection.

Method 2: Disable auto turn-off of Network device.

Go to
Network and Sharing Center. At the
right pane, click
Change adapter settings.
Right-click
on your
connection/network name
and go to
Properties.Click
the
"Configure..."
button and go to
Power Management
tab.Uncheck/disable
the
radio button
for
"Allow this device to turn off this device to save power". And then,
Restart the PC(Important).

Method 3: Reconfigure TCP/IP

To do this, follow these steps:

• 
  Run
  Command Prompt
  as
  Administrator.
  
• 
  Run
  these following commands:
  
  • 
    netsh int tcp set heuristics
    disabled
    
  • 
    netsh int tcp
    set global autotuninglevel=disabled
    
  • 
    netsh int tcp set global
    rss=enabled
    

For keyboard issue:

Method 1:
Run SFC Scan.  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Note:
Kindly run
SFC twice or thrice and check for results before you proceed to the next method.

Method 2: Reset Windows Update Components.

Resetting your
Windows Update Components
will allow you to
install
the update again including the
Text Services Framework. To do this, refer to
How do I reset Windows Update Components.

 

Network PC Win10 1903 issue Error Code 0x80070035

i followed these steps, but no matter what, i couldnt stop network list services.

"windows could not stop the network list service on local computer. error 1061: the service cannot accept control messages at this time".

also, which pc am i meant to be running this fix on? both PC's reported error 1061.