Windows 10: PC Crashes to blackscreen and reboots Kernel-Power Event 41 BugcheckCode 278...

Hi,As stated in the title my PC just randomly crashed into a "blackscreen" Both monitors losing signal followed by an automatic reboot.This has probably happened once before but I wasn't in front of my PC when It happened the first time, I just found my PC had rebooted when I returned.After browsing the web a bit I decided to check my Event log and found the "Kernel-Power Event 41" I also found out that this alone doesnt mean muchso I checked for a BugcheckCode and found 278, which I then looked up and has something to do with my GPU.My BugcheckCode with Parameters in detail:BugcheckCode278B

:)

 

Kernel-Power event id 41. BugcheckCode 0

Hello,

Thank you for writing to Microsoft Community Forums.

In-order to get more clarity on this issue and to assist you with appropriate troubleshooting steps, reply with answers to the below questions:

1. Are you aware of any changes made on your PC, prior to this issue?
   
2. Is this issue specific while playing a particular game?
   
3. Which edition of Windows are you currently using?
   

A Kernel Power Event 41 can occur in the following scenarios.

Scenario 1: The computer restarts, and there is a Stop error BugcheckCode in the event data.

Scenario 2: The computer is shut down by pressing and holding the power button.

Scenario 3: The system randomly restarts and no Stop error BugcheckCode is listed, or the computer is completely unresponsive (hard hang).

I suggest you refer the article on Kernel
Power Event ID 41 and follow the steps for the scenario that is causing this error on your PC.

Additionally, you can refer the article on Windows
Kernel event ID 41 error "The system has rebooted without cleanly shutting down first" in Windows
and check if that helps.

Regards,

Sandeep Kumar M

Microsoft Community – Moderator

 

Kernel-Power event id 41. BugcheckCode 0

Hello,

Thank you for replying with the required information.

What is the make and model of your PC?

As you have mentioned that the system randomly restarts and no Stop error BugcheckCode is listed, or the computer is completely unresponsive,
this scenario usually indicates a problem with the hardware. To help isolate the problem, I suggest you to refer the section
Scenario 3: The system randomly restarts and no Stop error BugcheckCode is listed, or the computer is completely unresponsive (hard hang)
from the following article on Windows Kernel event
ID 41 error "The system has rebooted without cleanly shutting down first" in Windows
and follow the steps mentioned in the section to isolate the cause of the issue.

If you see that the computer generates a Stop error that contains a BugcheckCode value that is not reported in an event ID 41, change the restart behavior for the computer. To do this, follow these steps:

1.
Right-click My Computer, and then click
Properties.

2.
Click Advanced system settings.

3.
Click the Advanced tab.

4.
In the Startup and Recovery
section, click Settings.

5.
Click to clear the Automatically restart
check box.

If the issue persists, I suggest you to follow the methods mentioned below:

Method 1: Perform clean boot.

Check if any third party application is causing this issue. Refer the article on
How to perform a clean boot in Windows
for steps to perform clean boot.

Note:
A “clean boot” starts Windows with a minimal set of drivers and startup programs, so that you can determine whether a background program is interfering with your game or program.

Your computer may temporarily lose some functionality while in a clean boot environment, however that functionality will return when you
reset the computer to start normally after you have finished your troubleshooting.

Method 2: Adjust PC to best performance.

To do that,

1.
In the search box on the taskbar, type
performance, then select Adjust the appearance and performance of Windows.

2.
On the Visual Effects tab, select
Adjust for best performance > Apply.

3.
Restart your PC and see if that speeds up your PC.

Method 3: Check your hard disk for errors.

To do that,

1. Double click on This PC icon.
2. Right-click the hard disk drive that may be damaged.
3. Click Properties, and then click the Tools tab.
4. Click on the Check option.
5. Now click on the Scan Drive option.

Regards,

Sandeep Kumar M

Microsoft Community – Moderator

 

Kernel-Power Error 41 Bugcheck Code 278

So when I generated this error, it went straight to a BSOD and got stuck there at 100%

I waited for a while and when it didn’t auto restart, I hard restarted it again

As for Kaspersky, I didn't have it installed before today. I installed it just to do a system scan earlier this evening

I had a question regarding the bugcheckcode 278 that was getting generated with the Kernel-Power event

I couldn't find anything that helped me with that anywhere

And that bugcheckcode has been constant whenever the system crashed these past few days, multiple times a day