Windows 10: Pc in a continuous blue screen loop.

Last week, I upgrade my CPU and motherboard. When booting up, it blue screened then restarted about 5 times before finally loading into the lock screen. After that, I had no issues unless trying to shut down or restart my computer, in which case it would blue screen loop a number of times again. Only today, however, it has become a continuous blue screen loop which will not even allow me to the lockscreen or into safe mode. I feel like I have had almost every blue screen message possible, most of which seem to be either hardware or driver related, although I'm fairly sure I have all the updated drivers available. The current blue screen loop just spits out the message "system_service_exception" before restarting.


I don't think I can aquire any crash reports or minidump files mentioned by other posts since I can't actually log on. Any help would be appreciated as I would rather not resort to resetting my computer completely.

:)

 

blue screen and error 0xc000021a and the continuous repair loop


blue screen and error 0xc000021a and the continuous repair loop
please help
Attachment 50235

Attachment 50236

 

Blue screen in terminal loop

Hi,

The blue screen error that you encounter can be triggered due to a possible hardware or hardware driver software failure. To isolate your concern, could you confirm if you have made any changes on your device prior to your concern? Also, are you getting
any messages for the blue screen error?

As an initial step to get out of the blue screen loop, we suggest that you perform a startup repair by booting to
System Recovery Options through a hard reboot. To do this, follow these steps:

• Turn on your device.
• When the Windows logo appears, press the power off button or unplug the power source to force shutdown your device.
  (If you're using a laptop, remove the battery. Note: Refer to the manufacturer's site on how to remove the battery of your device.)
• Perform this step three times. On the third time that you turn on your computer, wait for the
  Windows Recovery Environment (WinRE) window to appear.
• On the Choose an option screen, select Troubleshoot
  >Advanced options > Automatic Repair.
• Select Windows 10.
• If prompted, select an administrator account.
• Type in your password and click Continue.
• Wait for the repair to complete.

Once you're done, check if your device will boot normally.

We'll appreciate if you can send us an update.

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.