Windows 10: PC keeps running into a problem after hard resetting

I recently hard reset my computer to clean it up and now every few minutes it goes to a blue screen that says "your PC ran into a problem" and it restarts. It did not do this before the reset. Is there any possible fix for this?

:)

 

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.


First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".

 

router logs DoS attack from a local PC....

Well you did not say that you don't really know what you are doing. It's not a problem of course, but it changes things a little.

It's not even clear if the PC or the router is the problem at this time, so I suggested that you disable some unnecessary things which are usually known to cause many problems, sorry if those were too complicated.

• You could reset some network related stuffz on the PC as a next step. Open an elevated command prompt (run as administrator), and enter the followings on the PC:
  netsh int ip reset reset.log
  netsh int ipv6 reset
  netsh winsock reset
  netsh branchcache reset
  netsh advfirewall reset
  (note: You can export your current firewall rules in the "group policy" before the reset if it's needed for some reason)
  
  
• Btw, Would it be a problem to reset the router to the default settings if the things we are trying will not help? There is a menu point for that called "factory settings" (and also a little hole on the back if you prefer that one).. the Administrator username in the router after the reset would be admin and the password is probably on a sticker at the bottom of the router (special settings needed to go online with your ISP might be also necessary)
  This is not needed now (not yet), but perhaps the source of the problem is at the router and not the PC in question, so we may come to that eventually.

ps.: Do you have a second network card you could test in that PC and a different cable to rule out some hardware issues on the PC side?

 

After hard reset, OS disk showing no volumes/partitions

Hi everyone,

I've searched high and low on Google for the specific issue that I'm having, but I can't seem to figure this out.

About a year ago, I built my own computer. I have my OS (Windows 10) installed on a Plextor M6 256 SSD. Today, for about the fourth time in a year, my computer became unresponsive during normal use. After a forced hard reset, I was taken to a black screen with the 0xc00000e error, telling me that a required device was inaccessible. After a quick Google search, I found many answers saying that this problem was because of a corrupted boot record.

I followed the steps recommended by Microsoft. First, I attempted automated startup recovery. This didn't work. Then I attempted to use bootrec to fix the problem. This resulted in the tool telling me that no Windows installations were detected.

I decided then to open diskpart. The disk itself was detected, but whenever I listed volumes, nothing showed up for that disk. No partitions or volumes were listed.

I've since recovered the drive by flashing a Clonezilla image that I had as a backup, so everything is up and running now. However, I am curious as to why this problem keeps happening. I've downloaded the diagnostic tools from Plextor for my disk, and it says that everything is fine. I've also run a Windows memory diagnostic, which has returned no errors.

My assumption is that the hard reset is causing some kind of partition table corruption. But, that still leaves the issue of why the computer is freezing up to begin with unsolved. Any suggestions/possible causes to investigate would be much appreciated!