Windows 10: please help i just booted up my laptop and this happens i'm really scared it says system...

;Message

:)

 

laptop doesnt boot automatically

This is what happened.

1. Did a repair install and later disabled hibertnate in CMD.
2. Enabled legacy option ROM in BIOS.
3. After a few times startup ( i used the system in such mode for 5 days), changed boot option back to default.
4. Vola!! It boots automatically to win10 without any keypress. Tested it with many starts to confirm the same.
5. Re-enabled hibernate option using CMD and later selected Fast Startup.
6. System booted normally, without the need for any keypress.

I do not know exactly whether such steps resolved the problem or what else happened, hence cannot suggest above steps.

Many thanks to all members who helped to troubleshoot problems.

 

No Boot, Drives Not detected, Can't Load Win10 Pleses Help!

Until the BIOS sees your M.2, there's nothing you can do. It does not matter if the M.2 is unformatted/unallocated, the BIOS should see it.

1. Suggest that you take the M.2 out, clean all the contacts and re-seat it and hope this is the case.
2. If step one fails. Connect your 250GB SSD back in using one of the SATA port to see if the BIOS recognize it. If it doen't, then it might be something wrong with the MB, if it does then boot up the Windows Installation USB, run diskpart, shrink it at least 40GB then create a partition, Leave it unallocated then install Windows there.

Also try to re-seat all other components such as Memory, Video card etc...

 

My m.2 ssd is recognized in bios, but not as a boot device

Thank you very much for reaching out! As an Independent Advisor and fellow Microsoft user, I'm more than happy to assist you.

Here are some steps you can take to troubleshoot and potentially resolve this issue:

1. Check BIOS Settings

Ensure that your BIOS settings are correctly configured to recognize the M.2 SSD as a boot device:

• Enable CSM (Compatibility Support Module): Sometimes, enabling CSM can help the BIOS recognize the SSD as a boot device. You can find this option under the Boot tab in the BIOS settings.
  
• Set Boot Priority: Make sure the M.2 SSD is set as the first boot device in the boot priority list.
  

2. Update BIOS

Updating your motherboard's BIOS to the latest version can resolve compatibility issues with new hardware:

• Visit the ASUS official website to download the latest BIOS update for your ROG Strix B650 Wi-Fi motherboard.
  

3. Reinstall the SSD

Ensure that the M.2 SSD is properly installed:

• Remove the SSD and reinsert it firmly into the M.2 slot. Make sure it is securely fastened with the screw.
  

4. Initialize the SSD

If the SSD is new, it might need to be initialized:

• Boot into Windows using another drive, open Disk Management, and initialize the SSD as either MBR or GPT.
  

5. Check for Drive Mode Compatibility

Ensure that the M.2 slot you are using supports the type of SSD you have (SATA vs. NVMe):

• Some M.2 slots only support either SATA or NVMe, not both. Refer to your motherboard manual to confirm compatibility.
  

6. Repair Boot Configuration

If the SSD has Windows installed but is not recognized as a boot device, you might need to repair the boot configuration:

• Boot from a Windows installation USB, go to the command prompt, and use the following commands:
  
  
  This can help rebuild the boot configuration data.
  

7. Check for Hardware Issues

If none of the above steps work, there might be a hardware issue with the SSD or the motherboard:

• Test the SSD in another system to see if it is recognized as a boot device.
  
• If the SSD works in another system, the issue might be with the motherboard. Consider contacting ASUS support for further assistance.
  

Please feel free to reach out if you require any additional assistance. I'm here to help!