Windows 10: Randomly BSOD

I do not have a card to swap. How many hours do I have to test.
The aida64 test runs at 1360 MHz. 3DMark is working at 1360 MHz. 1360 is working in the unigine test. the software shows 1360MHz. But furmark shows 1240MHz.

 

That will be up to you. The longer the testing the more useful the results. It's important to monitor the temperatures with the longer testing. The problem has been narrowed down to the video hardware with the RSOD, BSOD, video drivers.
So it would be nice if a friend, neighbor, local computer store etc .could help with a swap or a method to make a confirmatory test.

 

Is the problem definitely on the graphic card?

 

The plan is to get more testing results.
So observe 24 hours with the new driver and if there are new bsod debug them.
Retest with FurMark.
It's getting closer but it would be nice to have a confirmatory test.

 

The initial bsod were indicating 0x124 WHEA and there are no longer any WHEA errors.
WHEA errors are highly indicative of hardware problems.

Clean all the fans again.
Re-seat the Video card again.

After the 24 hours to monitor for stability vs spontaneous BSOD plan to use Windows driver verifer to find problematic drivers.

Before using windows driver verifer
1) you must know the 3 methods to turn off windows driver verifer.
2) create a brand new restore point
3) back up any important files
4) create a back up image using Macrium:
Macrium Software | Your Image is Everything

5) This link has the custom test settings for windows driver verifier:
Microsoft Community

6) This link has the 3 methods to turn off windows driver verifier:
Enable and Disable Driver Verifier in Windows 10 Windows 10 Performance Maintenance Tutorials

Windows driver verifier will repetitively produce BSOD until misbehaving drivers are fixed or until it is turned off.
When there is a bsod you will use two software programs to analyze the bsod and then uninstall the driver. You can either rerun windows driver verifer to find the next misbehaving driver or install a replacement driver before restarting windows driver verifer. The end result should be the same and it is personal preference.
Blue screen of death (STOP error) information in dump files.
Resplendence Software - WhoCrashed, automatic crash dump analyzer

After there are no longer any BSOD you will run windows driver verifier for an additional 36 hours. If there are no longer any BSOD windows driver verifier will be turned off the this part of the troubleshooting will be completed.

Plan to perform the GPU stress testing with FurMark pending the results of windows driver verifier.

To get comfortable with the windows advanced troubleshooting menu open administrative command prompt and type:
shutdown /r /o /f /t 00
The computer will reboot to the windows advanced troubleshooting menu:
windows startup options (not startup repair) > select #6 safe mode with command prompt > type: verifier /reset
command prompt > Administrator X: \windows\system32\cmd.exe > type: verifier /bootmode resetonbootfail
restore
Using restore typically leads to a loss of the BSOD mini dump file and little progress is made in the troubleshooting.

For any new BSOD please post a new zip and we will guide you through the troubleshooting:
BSOD - Posting Instructions - Windows 10 Forums

 

I turned on the computer and entered bios. CPU was 29 degrees. Then I stopped at the bios, and after 7 minutes without doing anything, the CPU went to 55 degrees.

but in the prime95 test a maximum of 80 degrees

bios is 55 degrees too much?
full load 80 degrees to much?

and my proccesor base clock 3.5ghz turbo clock 3.7ghz but not working 3.7 ghz. maximum 3.6ghz.

 

Please update your progress with windows driver verifier.

For any bsod please post a new zip:
BSOD - Posting Instructions - Windows 10 Forums