Windows 10: Remove dual boot make win10 drive bootable

I installed windows 10 on 250GB Samsung SSD and had windows 7 on a M2 Kingston 250 GB using dual booting.I now want to upgrade the windwos 10 drive to a 1 TB SSD.When I removed the M2 Win 7 OS drive the windows 10 drive would not boot. I made sure it was selected in the BIOS I put the windows 7 drive M2 back in and now it boots dual boot. How do i make the windows 10 drive bootable? I want to clone the WIn 10 drive and put on the new 1 TB SSD.

:)

 

Missing Bootable devices in BIOS after removing Ubuntu dual boot

Windows 10 Pro, Version 2004, OB build 19041.572

I have a Gigabyte GA-Z77X-UP4 TH mb. My BIOS has been set to UEFI for a while now and I had no issues with it. When I needed to boot into some live cd or flash drive, I would press F12 at boot and have a list of bootable devices to choose from. I also saw all of these devices in the BIOS, where I could choose them for a boot order.

I found myself using Ubuntu quite often with the “try ubuntu” option, so last week I decided to install it as a dual boot. I used a secondary hard drive for the Ubuntu partitions (not C.) After a few days, I decided to get rid of the dual boot. I went through all the steps to delete it; deleting the ubuntu partitions, and using diskpart to get GRUB removed from the boot loader. Although after this, the computer would boot right into Windows, for some reason, the ubuntu was still listed in bcdedit /enum firmware, so I also used bcdedit /delete to delete that.

Here’s the issue that I have now:

When I press F12 to boot into a live CD (or flash drive), the only boot option is Windows. In my BIOS, in the boot order section, I can only choose Windows; there is no more list of all my drives and CD ROM to choose to boot from.

The only way to get back the list of bootable devices is if I switch the “Boot Mode Selection” from “UFEI only” to anything else, like “UEFI and LEGACY” or “LEGACY only.”

However, if I switch to anything other than “UEFI only,” the computer won’t boot into windows; I get an error saying, “Reboot and select proper boot device.”

I am 99% sure that before I did the dual boot, I had “UEFI and LEGACY” selected in the BIOS and in Windows System information, it would show that my BIOS is UEFI.

What I need now is to be able to see a list of bootable devices in my BIOS, including my CD ROM, so that I can choose to boot from a CD or flash drive when desired, and of course, that my computer should boot into Windows when I just want to boot normally.

Notes:

1. Fast boot is disabled.
2. I read that Secure boot should be disabled but I don’t have that setting.
3. I read that CSM should be disabled but I don’t have that setting.
4. My C drive (SSD) is GPT, Active & System.

Any suggestions?

 

Dual Boot Win7 & Win10

Here are my steps for dual booting:

• Create a system image - store it on an external drive
  
  
• Disconnect from the Internet and stay disconnected - part of the install asks about connecting
  - do NOT connect just yet.
  
  
• Create the space for the 2nd OS.
  This is tricky - drives initialized as MBR can only have 4 partitions (an extended partition allows for more),
  many OEMs create 4 primary parts and you have to adjust their disk schema.
  
  Post a Disk Management screen shotClose the left and right panes
  The columns should also be stretched to clearly show the values, most important is the Status column
  If you have many drives, you might have to adjust the middle separator and drag the bottom edge of the window down to show the maximum information.
  Then in the View menu, pick Top and change it to disk list - no need to post a pic - just note the initialized format (MBR | GPT) and post the information.
  
• Unless the 2nd OS will be used on a daily basis, keep the space to a minimum.
  Win10 + pgms on my machine takes up about 15 GB.
  I don't use Win10TP as my main OS - that's Win8.1, so data isn't a concern.
  30 - 50 GB is more than sufficient.
  
  
• Once the space is available - take your time here - there are traps with MBR disks.
  If your disk is initialized GPT, no problem - easy! But... MBR - make sure you know what you're doing.
  Just free up enough unallocated space,
  -> do not create a partition and do not format the space.
  
  
• When you're ready to install Win10, use a disc to avoid EFI issues.
  
  1. Boot to the Win10 install disc (see your machine documentation on accessing the Boot Order menu at startup)
     
     +editA
     These steps are probably NOT necessary, it was an afterthought when I installed Win10 the 3rd time as a dual boot to Vista. That is when I noticed the Win10 page file on my Vista boot drive - which caused Vista a bit of a problem (temporary page file created - yada, yada, yada) - I recreated the Win10 page file on it's own partition and then reallocated the Vista page file for good measure.
     
     At the first Win10 install screen, Press Shift+F10
     Then enter these commands in the Console window
     
     ^^ denotes comment, not a command
     Launch Diskpart
     lis vol
     
     ^^ remove the drive letters from all drives
     ^^ it's easier if you disconnect external drives that aren't needed for this exercise.
     
     sel vol #
     remove letter=
     ^^ specify the letter that was shown for that volume in the lis vol command
     ^^ repeat this (select volume, remove letter=) until there are no volumes with letters shown in lis vol
     lis vol
     exit
     close the Command prompt with the X in the upper right hand corner
     
     You should be back in the Win10 install now.-editA
     
     
  2. Answer the questions as if you were doing a clean installation (language, region, etc)
     
     
  3. Choose a custom install
     When it asks you where you want to install, choose the unallocated space
     Let the install complete, the rest should be easy.

+editB
When Win10 boots up, you shouldn't see any other drives - this is good.
Configure the volumes for each OS - I suggest that you keep the two OSes separate, only expose the volumes you need to for each OS. Your Win7 should see everything except the Win10 volumes. Your Win10 should only see volumes you'll use in testing (i.e. what ever you create on the currently new and blank SSD).
If you need data from your existing Win7 install, it's probably better to copy what you need than to expose your good data to Tech Preview code.
-editB

When Win7 boots up, you will see the Win10 drive - remove the letter from that drive. Keep your system separate.

If at any step above you need some help, please ask ... you might have to wait, please wait. The hardest thing to do is wait and the easiest thing to do is "ooops, but I thought you meant...."

I think I remembered all of the steps I took - but... I'm human too *Wink

 

dual boot

You initially asked:

is it possible to remove win 10 from dual booting?
Yes, of course it is!

What you probably wanted to ask is this:

• How to remove Win10 from dual booting
• How to remove Win10 from the disk

I already gave you an answer to your first question.

The answer to the second question depends on your disk / partition structure. Please use snippingtool.exe to post a picture of the Disk Manager frame (diskmgmt.msc).