Windows 10: Repeat of the windows update issues

I’ve lost count now how many updates have caused a fresh install or some kind of troubleshooting immediately after restarting. This time it just sits at the boot screen. Whenever I get it to automatic repair or go into the repair environment it goes to a black screen. Whenever I try to use a recovery drive to get to the repair environment it just sits there on the blue screen. The M.2 SSD I have Windows on was installed back around August or September. Latest try while I type this after “booting” to the usb is just sitting at the blue screen and not even getting to the point where you choose install or repair. Just made a fresh win install usb drive and getting the same.

People always complained about older versions of windows years ago but I’ve never had these kinds of problems until windows 10...acts like a virus.

submitted by /u/mach_250
[link] [comments]

:)

 

MSI 5870 BIOS Update

Still can't reproduce. Could you please post the exact BIOSes that produce the issue?

 

User.000 issue after updating to 1909

I'm one of the many people suffering from issues with user profiles after applying Update 1909 to Windows 10. I've read all the threads I can find on the topic here and have followed the suggestions, all to no avail. Any other thoughts are appreciated.

After applying Update 1909, the ProfileImagePath was changed to c:\users\User.000
One file that was always in use and couldn't be removed was left in c:\users\User (can't recall or find the exact file now), so I could never rename or remove the c:\user\User directory.

I followed the multiple suggestions from Brink and others:

• Rebooted at least 6 times
• Enabled hidden Administrator
• Booted into Safe Mode
• Changed ProfileImagePath
• Tried to rename c:\users\User but couldn't because a file was still in use
• Copied all data from c:\users\User.000 into c:\users\User
• Rebooted and had temporary profile
• Followed steps in Brink tutorial to change ImageProfilePath; rebooted with no change
• Restored using Restore Point from before Update 1909 - returned to single profile state (User.000)
• Removed each update that was installed individually and rebooted after each update removal - profile state never changed
• After all updates were removed, repeated the steps above with hidden Administrator, changing profile, etc. - same issue with file in use in c:\users\User
• Followed all steps above with hidden Administrator but without copying files from User.000 to User - same results

Any suggestions are greatly appreciated!

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.