Windows 10: Samsung SSD is not detected in Windows and only read in BIOS

Please help me, I have a Samsung SSD 970 EVO Plus, at first it worked as it should, then a bluescreen error occurred and suddenly it just disappeared from Windows and was only read in the BIOS. can anyone help ?

:)

 

Installing SSD not detected by BIOS

Sequence of installing new SSD.

1. Disconnected the HDD with Windows.
2. Fitted Syba 4 Sata PCI-E card
3. Fitted Samsung 500GB 860 SSD connected to Syba 4 Sata PCI-E card
4. Installed Windows 10 Home in Samsung 500GB 860 SSD

​Windows installed fine in the SSD. Entered the BIOS to set the SSD as 1st Boot priority but the BIOS has not detected it. The only boot devices shown in the BIOS are the CD/DVD Rom and the Replaceable Device. *Mad
Device Manager shows the SSD connected.
I connected the the HDD which still has Windows installed but I get the message to "Reboot and Select Boot Media" even though the SSD is still connected. *Eek
Any help would be most appreciated.

Just noticed while safe removing USB memory stick that the SSD shows as a removable drive C\:!!!! *Eek

 

Win10 clean install on Samsung SSD 850 EVO

BLUF: SSD is not listed ubder "Where do you want to install Windows?"

Steps Complete:

1. I've create a Win10 bootable install usb.

2. I connect the new Samsung SSD 850 EVO via SATA.

3. I reboot PC and verify SSD is seen by the motherboard/BIOS

4. Begin Win10 install via usb.

5. Get to "Where do you want to install Windows?" and the SSD is not listed

Problems:

1. Samsung does not offer a driver for the 850 on their website

2. Cannot locate driver elsewhere

Unsuccessful Mitigations Steps Attempt:

A. Format & partition SSD via Windows Disk Management, then retried steps 1-5 above....same result

B. Clone existing HHD onto SSD via "Image for Windows" by TeraByte, then verified SSD contents via Windows Explorer....similar result

Can you please offer some advice on locating a driver for a Samsung SSD 850 EVO 1TB drive? Or an alternative method?

Thank you

 

SSD is not detected in BIOS

Hi Joey,

Thank you for writing to Microsoft Community Forums.

We understand how difficult it could be. However, could you please let us know was there any major change on your system prior to which you weren’t facing this issue?

Meanwhile, we would suggest you to follow the methods mentioned below and check if it resolves the issue.

Method 1: Change BIOS settings.

1. As you have mentioned, you are able to boot the system in safe boot, restart the system and enter
   BIOS setup.
   
2. Expand System Configuration and click on
   SATA Operation.
   
3. Change the SATA Operation mode to AHCI from either IDE or RAID.
   
4. Save changes or Apply
   and ExitSetup.
   
5. Reboot once more and Windows will automatically start the AHCI drivers.
   
   BIOS Disclaimer: Modifying BIOS/ complementary metal oxide semiconductor (CMOS) settings incorrectly can cause serious problems that may prevent your computer
   from booting properly. Microsoft cannot guarantee that any problems resulting from the configuring of BIOS/CMOS settings can be solved. Modifications of the settings are at your own risk.
   

After following the steps above, if the SSD is being detected. Please follow
Method 2.

Method 2: Rebuild BCD from command prompt (This method needs bootable media).

If the bootable media is not created, you can refer this link to

Create Windows 10 installation media, please refer this section on 'Using the tool to create installation media (USB flash drive, DVD, or ISO file) to install Windows 10 on a different PC' for the steps to create installation
media.

1. Insert the bootable media for Windows 10, and restart your PC.
   
2. Press on any key to proceed.
   
3. Select a language and click on
   Next.
   
4. Click on Repair your computer option.
   
5. Click the operating system that you want to repair and then click
   Next.
   
6. On the Choose an option screen, select
   Troubleshoot > Advanced options > Command Prompt.
   
7. Type BOOTREC /FIXMBR, and then press
   ENTER.
   
8. Type BOOTREC /FIXBOOT, and then press
   ENTER.
   
9. Type BOOTREC /SCANOS, and then press
   ENTER.
   
10. Type BOOTREC /REBUILDBCD, and then press
    ENTER.
    
11. Restart your PC.
    

Regards.