Windows 10: Seagate XM1441 1.92TB - does it mean 1.92TB after or before format?

i was wondering about theses obscure memory SSD's. are they measuring in decimal or binary? will i get 2tb and then it will format down to 1.92TB or will i get 1.92TB and format even lower?

:)

 

How To Format A Write Protected Flash Memory ?

¿You already tried this one?...

Run CMD


1. diskpart
2. list disk

Then in the 3º step, put the correct number of disk in the list for the usb flash (if it's listed in disk 3, then you'll have to write select disk 3).

2. select disk #
3. clean
4. create partition primary
5. select partition 1
6. active
7. format fs=fat32
8. assign
9. exit

with that commands you will format the flash drive in fat32, if you have a large drive you can select also "format fs=ntfs" in step 7.

good luck!

 

Not able to format 512GB Crucial MX100 (SDD#1)


October 2016

Hi everybody,
Like I say in the topic I can’t format my SSD#1 Crucial MX100 512GB.
Here what I try. Thanks.

Operating System: Windows 10 full updated (October 2016)
Computer: Asus Maximus Formula (buy at 2008)
BIOS: Legacy BIOS (mean no UEFI - Unified Extensible Firmware Interface)

BIOS and Windows 10 recognized the SDD#1.

----------------------------------------------------------------------------------
1- I try Disk Management to format the SDD#1.
One with “Quick format” option check and one with “Quick format” uncheck.

Same result for both:
The windows message received:
“Virtual Disk Manager” (title of the windows showing the message)
The format did not complete successfully (the message)
----------------------------------------------------------------------------------
2- For this step I just connect the SDD#1 and the CDROM
I try to boot from Windows 10 DVD installation, choose “Install” and Windows is not able to delete the partition on the SDD#1. It is not able to create a partition neither. And sure it’s not able to install Windows 10 on the SDD#1.
----------------------------------------------------------------------------------
3- For this step I just connect the SDD#1 and the CDROM
I try to boot from Windows 10 DVD installation, choose “Repair”, go in command prompt and do the following:

Diskpart
List disk
List volume

Select disk 0
Select volume 1
Clean

Message received:
DiskPart has encountered an error: The request could not be performed because of an I/O device error. See the System Event Log for more information.
----------------------------------------------------------------------------------
4- For this step I connect all my SDD#1 and HDD and put the SDD#1 on other port.
I go to CMD and enter the same command than above for same result.
This time I can check the Event Viewer:

Event Viewer
464 Error and 1 Warning

Warning
Event Properties - Event 153, disk
The IO operation at logical block address 0x0 for Disk 2 (PDO name: \Device\0000002a) was retried.

Errors (repeat the following errors 232 time ? - I don't check all but it appear to be same two errors)
Event Properties - Event 24620, BitLocker Driver
Encrypted volume check: Volume information on \\?\Volume{01128aa1-0000-0000-007e-000000000000} cannot be read.

Event Properties - Event 7, disk
The device, \Device\Harddisk2\DR2, has a bad block.
----------------------------------------------------------------------------------
5- I try the free program “ MiniTool Partition Wizard Free Edition 9.1” and nothing work. Not able to delete partion not able to create one.
----------------------------------------------------------------------------------
6- I try GParted under XUbuntu and it’s not work too.
----------------------------------------------------------------------------------

I am very sad. I do not have $ 200 for buying another SSD.
Are there something to do to format the SSD # 1?
I can’t believe it's broken. I have hard disks (trays) much older than it and that still works

 

Windows 10 not detecting my seagate 1 TB external hard disk

Hi,

Thank you for coming back to us with the status.

To understand the issue better, I would like to know what exactly happen when you try to open the file?

Let’s try simple steps and check if this helps. I would recommend you to connect the external hard disk on different computer and check if you are able to open the files.

I also, suggest you to go to the Disk Management and check if the drive are detecting on the system.

Press Windows + R and type diskmgmt.msc on the box and hit
Enter.

Method 1.

For now, I suggest you to go to device manager and update Seagate driver and check.

• 
  Press Windows key + X and select
  Device Manager.
  
• 
  Click on Universal Serial Bus to expand, right click on the Seagate
  device and click on Update.
  

If the issue still persist, you can try the below method.

Method 2.

I suggest you to connect the SD card to the system and run check disk on the hard drive to see if there are any corruptions. Follow the below steps:

• 
  Press Windows key + X, click Command Prompt (Admin).
  
• In the Command Prompt, type the following command, and then press ENTER:
  
  chkdsk /f

Disclaimer: While performing check disk on the hard drive, if any bad sectors are found then check disk will try to repair that sector. Any data available on a bad sector might be lost. Once Check Disk completes, boot
the computer and then check.

Hope this helps. Keep posting us with status we will be glad to help you.