Windows 10: Some programs that rely on drive letters might not run correctly. Do you want to continue?

Assalamualaikum. I have getting some issues from my computer please help me. Okay, I explain. My laptop has 256 SSD. there have 3 partitions which are Local disk C this drive I was setup Windows, then New Volume D, and New Volume E. My Windows drive Local Disk C doesn't have enough space. That's why I want to extend my 'C' drive. and I want to shrink the 'D' drive. Now when I shrink my 'D' drive it works perfectly but the problem is when I change the 'D' drive letter like New Volume D to New Volume F then I am getting --------------------------- Disk Management --------------------------

:)

 

How do I change the letter designation of installed hard drive

Hi, my name is Kelly, and I'm an independent consultant and I'm here to help.

You can change the drive letter designation of your hard drive using the Disk Management utility in Windows. Here are the steps to do so:

Press the Windows key + X and select "Disk Management" from the menu.

Find the hard drive you want to change the letter designation for. It will be listed in the bottom half of the Disk Management window.

Right-click on the partition of the hard drive you want to change the letter for, and select "Change Drive Letter and Paths".

In the window that appears, click "Change".

Select a new drive letter from the drop-down menu.

Click "OK" to save the changes.

If you receive a warning message about programs that may rely on the drive letter, click "Yes" to continue.

Once you have completed these steps, your hard drive will have a new letter designation. It's important to note that changing the letter designation of a drive may affect the functioning of some programs that rely on specific drive letter assignments. Therefore, it is recommended to proceed with caution and backup any important data before making changes.

 

2nd and 3rd hard drives show two drive Letters

Hello Andre: I followed the instructions carefully and this is what this process amounted to. I followed this step by step.

Press Windows key + X - Worked fine

Click Disk Management - Worked fine

If you see your drive listed there, but no drive letter, right click it -
All my drives showed up with there drive letters. When I clicked on the drive - Local Disk (D) (I. The panel came up " change drive letter and path.

Click Change Drive Letter and Paths - for local disk (D)" and in the panel it said "Allow access to this volume by using the following drive letter and paths". In
the panel that shows up it shows a drive icon and the letter I: . Below this are the options to ADD, CHANGE and REMOVE.

Click Add - When I click the ADD button a new panel comes up and the only option allowed is "Mount in the following empty NTFS folder". When I enter the letter D:
( the drive letter I'm trying to get too) and click on the OK button it opens a new panel comes up and tells me "The device is not ready".

Click Assign the following drive letter - I then go back a few panels and select CHANGE, this time the same panel opens up but this time the other option is locked
in as my only choice - "Assign the following drive letter". I enter D: again and in the pull down menu the letter D is not available for me to choose.

Click in the Drive letter list box - Then I go back to the previous panel and select REMOVE, now the new panel tells me "Some of the programs you rely on drive letters
might not respond correctly. Are you sure you want to remove this drive letter. I did not proceed as I've done this before and it does remove the drive letter I: but the in Disk Management the now D: dive is no longer accessible.

So now I have explored all three options that were presented when I right clicked on the "Click Change Drive Letter and Paths" In the end I was not able to remove the drive letters I and J from disk management

Thanks very much for the assistance, do you have any other suggestions I can use to correct this issue? I thought I might try deleting the D letter leaving the drive letter I, then going back in and try changing that
drive letter back to D done in two separate steps??? Bill

 

Drive Letters Changing

Hello Karen I’m Virginia an independent advisor here.

I apologise if this is an obvious question but are you clicking OK after changing the drive letter?

Are you following the instructions correctly?

In Disk Management, right-click the disk for which you want to change or add a drive letter, and then select Change Drive Letter and Paths.

Disk Management showing a drive

To change the drive letter, select Change. To add a drive letter if the disk doesn't already have one, select Add.

The Change Drive Letter and Paths dialog

Select the new drive letter, select OK, and then select Yes when prompted about how programs that rely on the drive letter might not run correctly.

The Change Drive Letter or Path dialog showing changing the drive letter.

You can also try a different drive letter to see if that will stick, if it does change it back to E, if that doesn’t stay then change it back to a different letter.

A drive letter will change if a drive with the same letter is connected first - an example is I have external hard drives & SD card, if I connect the SD card first then that is E, if I connect one of the hard drives first that will be E & then connecting the
SD card that will be come F, I have to go into disc management to set the drive letters as posted above.

If you are correctly following this tutorial & are still having problems please post back.