Windows 10: System crashes while using clearcase 8.0.1.x /9.0.1.x (checking out files) on windows 10...

After upgrading system to Windows 10 - os 1803 we are getting below issues while working with clearcase 8.0.1.x/9.0.1.x

Unable to checkin/checkout. Not able to create views. Not able to add any file to source control.

System hangs & crashes while performing any clearcase operation.

Please let us know if there is any issue with the windows 10 ver(1803), any security system enabled ? ,or has clearcase provided any fix? we have tried 9.0.1.5 and issue still persists.

Working fine with windows 10 ver 1709.

Thanks in advance.

:)

 

System Reserved Partition on Disk 1 not Disk 0

The results were the same as before: Windows is installed in a single 477 GB partition on Disk 0 and the System Reserved is in a 500 MB partition on Drive 1. The rest of Drive 1 is unallocated. This is identical to the configuration I had when I asked the
question.

The Media Creation Tool used to created the install ISO DVD is v. 10.0.14393 downloaded on 12/13/2016.

I followed your instructions:

• I selected Drive 0 and deleted the existing Windows partition.
• I clicked New and Apply. Windows then formatted Drive 0 as a single primary partition.
• The existing System Reserved partition was still on Drive 1.
• So I deleted the System Reserved partition on Drive 1 and the just created Primary partition on Drive 0
• I then selected Drive 0 and clicked New and Apply again. Same result a single Primary partition on Drive 0. Drive 1 was left unallocated.
• Upon completion of the install
  • Windows occupies about 15 GB in the only partition on Drive 0
  • The 500 MB System Reserved partition was placed on Drive 1
  • The rest of Drive 1 is unallocated.

How can I get the System Reserved partition to be placed as the Partition 1 on Drive 0 with Windows installed in Partition 2?

Thanks.

Bill

 

System Reserved Partition on Disk 1 not Disk 0

My PC was dual-boot with the 500 MB System Reserved and Primary System partitions on Drive 0 and the Secondary (2nd on added) on Drive 1. Then I started having boot problems which apparently were caused by Disk 0 errors. I would often get "Scanning and repairing
drive" notification during bootup. Then Windows went through some extensive repairs during one boot attempt and added a 500 MB Recovery partition in an unallocated area of Drive 1 after the System partition. I think it was called Recovery. Eventually the computer
wouldn't boot at all.

Now I've replaced the Drive 0 HDD with a 500 GB SSD drive and completed a clean install of Windows 10 on a New 200 (195.31) GB partition on Drive 0 with the intention of the System Reserved partition being added by the Windows installer before the System
partition on Drive 0. That's not what happened, the 500 MB Recovery partition on Drive 1 was replaced with the System Reserved partition. So, I repeated the Windows 10 clean install on SSD Drive 0 and deleted all partitions on Drives 0 & 1 before adding a
New 200 (195.31) GB partition on Drive 0 and selecting Drive 0 for the Windows 10 install. Windows again placed the System reserved partition on Drive 1.

Why is Windows insisting on installing the System Reserved partition on Drive 1?

What do I need to do to get Windows to place the System Reserved partition ahead of the System partition on Drive 0 leaving Drive 1 completely unallocated?

Thanks.

Bill

 

system restore unsuccessful with error code 0 x 80070057

Thank you Sayan for the reply.

I managed to run the first two Dism commands successfully as you indicated but the third Dism command was unsuccessful and generated an error message as follows :

".Error: 0 x 800f081f

The source files could not be found.

Use the "Source" option to specify the location of the files that...

see
http://go.microsoft.com/fwlink/?LinkId=243077.

The DISK log file can be found at C:\WINDOWS\Logs\DISM\dism.log "

How on earth am I supposed to find ths location of the source files ?

Help ?

Go to C:\Windows\Logs\DISM

You will find the file there!

or copy paste the above in windows explorer(My computer)

Thank you Daksh,

I'm sorry, am somewhat puzzled. The only file in that directory is dism.log. Need heavy guidance.

How do I use the "source" option to specify the location you suggest ?