Windows 10: TuneUp 2.7.0.1 Setup

Team - since reverting back to the normal release from the insider release. The TuneUp setup will not complete with the error message of :Error setting output path to: " C:\ProgramFiles\\WindowsApps\AppleInciTunes_12100.7.42015.0_x64_nzyj5cx40ttqa\Plug-Ins'. Exiting installer. Can someone advise?

:)

 

Tuneup 2012

Hi Donald,

Follow these steps to remove Tuneup 2012:

• Press Windows key + X.
• Click on Programs and features.
• Find Tuneup 2012 from the list.
• Right click on the Tuneup 2012 and select Uninstall.

Hope it helps. If you have any other questions, please do not hesitate to reply. We will be glad to assist you.

 

Intel Updates Core 2 Quad Q9550 to E-0 Stepping

We continue our Monday news list with another Intel story that brings to our attention information concerning the company and more specificly its 2.83GHz Core 2 Quad Q9550 chips that will move from the current C-1 to the newer E-0 stepping. The updated chips will start selling on August 22nd, featuring the following changes:

• New SSpec and MM numbers for the converting products
• CPUID will change from 0x10677 to 0x1067A
• Package change to Halide free package

Apart from that, the new stepping CPUs will not include any other changes. Of course, like most new stepping parts a BIOS update will be needed.


Product Change Notification 108663 - 00

Source: TechConnect Magazine

 

Want to setup Raid 0

is the OS going to be on the raid or on a separate HDD?



best option would be to have the OS on the raid 0 to avoid any problems down the road... since you only have one sata controller...

i could not install my os onto a separate HDD with all 3 drives connected to the same controller with my raid 0 ... i had to move my OS drive to the jmicron controller.


as for the actual setup of your raid... assuming you are only connecting 2 hdd's to your controller.. it will be simple. (checking up on your bios/south bridge config... will post how to set it up in a few)


Step 1

if your only using 2 hdd's to create a raid 0, connect both drives .. one to sata port 4... the other to sata port 5.

Step 2
boot into your bios and go into "intergrated peripherals".. then chainge the following settings.
ensure stat controller is "enabled". then change the setting for "stat Port 4/5 to "as raid type".

save your bios and exit

Step 3

reboot your pc, and let it post. it will then get to your raid screen and tell you no raid is definded... go ahead and press ctrl-F to enter raid setup.
0.

Step 4

once in raid setup. press <2> to create a raid.
1. Under the RAID Mode section, press the <SPACE> key to select RAID 0.
2. Set the Stripe Block size. 64 KB is the default.
3. Under the Drives Assignments section, press the up or down arrow key to highlight a drive.
4. Press the <SPACE> key or <Y>to change the Assignment option to Y. This action adds the drive
to the disk array. The Total Drv section will show the number of disks assigned.
5. Press <Ctrl>+<Y> keys to save the information. The window below will appear.
7. Press <Ctrl>+<Y> to set the capacity of the RAID array or press other keys to set the array to its
maximum capacity.
8. After the creation is complete, the screen will return to Define LD Menu where you will see the
newly-created array.
9. Press <Esc> to return to Main Menu and <Esc> to exit the raid setup.

Step 5

from here your ready to install windows... you may need to put your motherboard disk in during setup to add the drivers for your raid if it cannot find it.