Windows 10: Unable to upgrade to windows 1903. Getting multiple errors that change after a reboot.

Unable to upgrade to windows 1903. Getting multiple errors that change after a reboot.

:)

 

Unable to upgrade to windows 10 build 1903, AMD RAID Driver Error

I am currently trying to install the windows 10 1903 build update, my current version is 1803. I get the following error message, claiming that my RAID driver is outdated and needs to be updated first:





However I have updated the appropriate driver, and restarted my computer multiple times, and still get the exact same error message when trying to update. I have even confirmed that the driver is the correct updated version, as my version is now 9.2.0.127 as can be seen here:






According to the microsoft help for the error message: "version 9.2.0.105 and later versions of the AMD RAID drivers do not cause this issue" so the update should now be working.

I have tried deleting the contents of both:
C:\Windows\SoftwareDistribution
and
C:\Windows\System32\catroot2
in an attempt to reset the update so that it recognizes that I have the correct driver now but nothing has worked.

I cannot figure out why I am still getting the error message, which is preventing me from updating. Any help is greatly appreciated.

 

Unable to upgrade to windows 10 build 1903, AMD RAID Driver Error

I followed these steps exactly, and did not get the error message this time. When the update finished installing in windows, I was prompted to reboot to finish installing. After about 5 minutes of installing the update crashed to a bluescreen windows stopcode
error: KERNEL_SECURITY_CHECK_FAILURE. My computer then started to reboot, and told me it was rolling back the update progress I had made, and returned to windows.

To address the KERNEL_SECURITY_CHECK_FAILURE I ran windows driver verifier, as well as system file checker. System file checker told me some files were repaired and then prompted me to reboot to fix remaining files that had not been fixed.

Upon reboot I entered a bootloop and was unable to enter windows. I tried windows startup recovery multiple times, as well as creating a bootable usb with the latest version of windows 10 (1903) to attempt startup recovery. Nothing worked and the bootloop
continued. I was able to enter windows using safe mode, but no other way.

I then booted from my Macrium Reflect rescue media drive, and restored my most recent system image, from 10 days ago, made with Macrium Reflect. I am now booted back into windows, albeit with my OS in the state it was 10 days prior. This means I am back
to square one, with version 1803 of windows and a pending update to version 1903 which will likely not work.

I am currently running a system file check from cmd and whave decided to switch my RAID setup from using AMD Raidxpert to windows raid. After this is complete I will remove all AMD raid drivers from my computer, and attempt the update to 1903 again.

 

Unable to upgrade to Windows 10 with error: 0xC1900101-0x4000D

Hi Patrick,

Thank you for posting in Microsoft Community, we appreciate your interest in Windows 10.

I understand the inconvenience you are facing with upgrading to Windows 10, we will help you with this issue.

Do let us know:

• Have you connected any external devices except mouse and keyboard to your device?
• What is the complete error code/ error message of this issue?
• Are you able to access the computer?

Step 1: I suggest you to remove all the external devise except mouse and keyboard, hard reboot the computer and check with the status of this issue.

Step 2: I recommend you to refer to the below article by Andre Da Costa and check if it helps.

How to: Troubleshoot common Setup and Stop Errors during Windows 10 Installation

Refer to the section: 0xC1900101-0x4000D - The installation failed in the SECOND_BOOT phase with an error during MIGRATE_DATA operation,
perform the troubleshooting steps mentioned if your issue matches with the same.

I would like to infirm that, if you are unable to upgrade to Windows 10, you can use Windows 10 ISO file, create a Media creation tool and try to upgrade your computer.

Refer:
How to: upgrade from previous versions of Windows using Windows 10 ISO file

Hope it helps. Reply to the post with an updated status of this issue, we will be happy to help you further.