Windows 10: updater.exe

Every time I turn on my Windows 11, Windows PowerShell will open itself 4 times, I'll get another pop up from Windows Installer and it says, "This installation package could not be opened. Verify that the package exists and that you can access it or contact the application vendor to verify that this is a valid Windows installer page." Then I'll get a 6th pop up that says, "Do you want to allow Updater.exe make changes to your laptop?" I usually put no; in fear it may be a virus. But how do I get rid of this it's scaring me

:)

 

Windows Updated(16299.309).KB4088776 Restart is required to complete.

Hi dalchina. Good news, I followed your suggestion and reinstalled the update and now it appears as "installed correctly" *Biggrin Maybe it was not necessary to run the Windows Update Troubleshooter or maybe if necessary. But using it I do not think it could have worsened something. The installation was very fast, unlike the first time it showed step 1 and step 2 completed.

Thanks for the suggestions and for the time to respond Best regards.


And thanks for the tip of that program, I'll have it on my list.

 

we couldn't complete the update kb3135173

Hello,

I'm sorry to inform you that your method 2 was unsuccessful.

For printer problem, I already contact HP but it seems that I need to make sure windows update work first.

Back to Method 2, are you sure this method also work for windows 10?

Anyway, I follow those steps and these what I encounter:

• net stop appidsvc: cmd "Application identity service is not started"
• net stop cryptsvc: There was a y/n question. My replay was Y.
• Step 4. In the first tried, I skip the 4th step.
• Step 6. There are several dll that either "failed to load" or "loaded but "entry point DllRegisterServer was not found". I didn't read all the error message, but this are dll that show error message:

• regsvr32.exe mshtml.dll
• regsvr32.exe shdocvw.dll
• regsvr32.exe browseui.dll
• regsvr32.exe msxml.dll
• regsvr32.exe gpkcsp.dll
• regsvr32.exe sccbase.dll
• regsvr32.exe slbcsp.dll
• regsvr32.exe initpki.dll
• regsvr32.exe wuaueng.dll
• regsvr32.exe wuaueng1.dll
• regsvr32.exe wucltui.dll
• regsvr32.exe wuweb.dll
• regsvr32.exe qmgr.dll
• regsvr32.exe qmgrprxy.dll
• regsvr32.exe wucltux.dll
• regsvr32.exe muweb.dll
• regsvr32.exe wuwebv.dll

• Step 10 i skip this.
• Are you sure step 11 need to be avoided and not step 10?
• I restart my computer, run windows update, no luck. Try those steps again with step 4 included.
• step 4.a. Ren %systemroot%\system32\catroot2 catroot2.bak
  "access denied".
• for step 6, still the same.
• Restart, no luck.

Now, what should I do?

By the way: I already uninstall HP printer driver, but strange enough windows update still show that there are update for the printer. Tried to install, error though.

 

Intel E5200 Gets Updated, R0 Stepping Coming Up

Intel's Pentium Dual-Core E5200 processor is getting on course for a specifications update. The chip will feature in a new, improved Wolfdale-2M core, spec'd out as the R0 stepping, from its current M0 stepping. The new stepping is intended to add new instructions, power-management features, and bring about changes in the chip-package. A short list of known changes is as follows:

• CPUID changed from 10677 to 1067A
• Power State Indicator (PSI) support with Intel 4 series chipsets
• New instructions - XSAVE and XRSTOR
• New S-spec and MM numbers
• New halide-free chip package

Due to the changed CPUID, users may require BIOS updates to detect the CPU. According to the company, E5200 R0 should be out by April 13.

Source: TechConnect Magazine