Windows 10: USB boot gives blue screen

Hello, I have a mostly new build pc I want to add old harddrive later on, now using a new SSD, but I get stuck at installing windows 10.I have a new gigabyte B550M DS3H motherboard, MSI graphics card not new, new processor amd ryzen, new ram and new SSD.I have made a bootable USB using rufus media creation tool gave errors. The USB is 32G, and was new on my first attempt.First I had GPT partitioning. That seemed to work installation started after I selected language etc, but then gave a message that there had been an error no mor specific information or error code given. More aat

:)

 

USB ports fail, then blue screen of death on three Windows 10 computers -- Can this be fixed or is this caused by a virus?

Hi Grace,

It's possible that certain drivers, such as USB and other device drivers are causing blue screen errors on your PC. Another factor is due to a conflicting third-party software. Now, before we get into the solution, were you able to boot your computer normally
or can it boot to the desktop screen? If yes, then we suggest that you run the
Hardware diagnostic tool on your PC. Just type troubleshooter on the
Search box, press Enter, then look for
Hardware and Devices, and click Run the troubleshooter.

If the troubleshooter didn't resolve the port issue, then might as well you update the USB driver, and the BIOS firmware of your computer.

In addition to that, if you're still getting a blue/black screen error after performing the recommended steps, then we suggest that refer to the troubleshooting steps from these articles:

• Troubleshoot blue screen errors.
• Troubleshoot black screen or blank screen errors.

Let us know the outcome.

 

Startup Blue Screen

Hi Jon,

Startup blue screen error(s) can occur if a problem causes your PC to shut down or restart unexpectedly. It could be due to the following:

• Outdated device software drivers
• Corrupted Windows update system files
• Software/Security conflicts

We would like to know some information:

• Did you get any blue screen stop error codes?
• Have you tried booting in Safe mode?

We suggest that you check this
article about troubleshooting blue screen errors and follow the troubleshooting steps provided there.

We will wait for your response

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.