Windows 10: What format should be used for storage drive read/write both Windows 10 and Linux

I have an hdd that I intend to use as a storage drive for files from both windows 10 and Linux. What format should be used for this storage drive ?

:)

 

How To Format A Write Protected Flash Memory ?

¿You already tried this one?...

Run CMD


1. diskpart
2. list disk

Then in the 3º step, put the correct number of disk in the list for the usb flash (if it's listed in disk 3, then you'll have to write select disk 3).

2. select disk #
3. clean
4. create partition primary
5. select partition 1
6. active
7. format fs=fat32
8. assign
9. exit

with that commands you will format the flash drive in fat32, if you have a large drive you can select also "format fs=ntfs" in step 7.

good luck!

 

Format an external Drive.

Hello Roger,

Thank you for posting your concern in Microsoft Community and welcome to the Windows 10 Family.

I would suggest you to follow the below steps to format the drive you are referring to.

• Right Click on Start menu and select Open Computer Management.
  
• 
  In the left pane, under Storage, click Disk Management.
  
• 
  Right-click the volume that you want to format, and then click Format.
  
• 
  To format the volume with the default settings, in the Format dialog box, click
  OK, and then click OK again.
  

Note: You cannot format a disk or partition that is currently in use, including the partition that contains Windows.

Hope it helps.

Thank you.

 

Error: "Scan the drive now and fix it", Linux named folder with special characters are not accessable in Windows 10 using external hard drive

Hi,



Thank you for writing to Microsoft Community Forums.



May I know the file partition format type of your external drive?



As Linux and Windows they work on different file system, when the files are migrated from Linux base system to Windows OS, most of the files that are not supported could be hidden, I suggest you to follow the steps below to further
narrow down the root cause of the issue.



Method 1: Check the hard drive in different computer.



I suggest you to check the hard drive in a different computer and check if you still face the issue.



If the same issue persists on different computer then the issue might be with the hard drive itself, I suggest you to contact the local tech and get the drive checked.



Method 2: Run Check disk.



Run the check disk command to repair the hard drive and fix the bad sectors.

1. Search for Command Prompt on the start menu.
   
2. Right click and Run as Administrator.
   
3. Type in chkdsk C: /f /r /x where
   C: represents the drive letter for the hard drive change the drive letter according to your system and hit enter.
   

Disclaimer: While performing chkdsk on the hard drive, if any bad sectors are found on the hard drive then chkdsk tries to repair that sector if any data available on that might
be lost.



Method 3: Automatically diagnose and fix Windows USB problems.



I suggest you refer to this article
Automatically diagnose and fix Windows USB problems
download and run the troubleshooter to fix the issue with USB detection.



Method 4: uninstall USB drivers.

1. If you still face the issue and the hard drives throws the error again, you can refer the article
   
   USB devices may stop functioning correctly when multiple devices connected to the same USB hub go into selective suspend and check if this helps you.
   
2. Reboot the computer once after the steps are completed.
   

Method 5: Backup your data on Linux OS.



As the drive is compatible with Linux system, I suggest you to backup your data on any Linux computer first.



Method 6: Check for hidden files.



Some Linux files that are not readable by Windows are sometimes hidden in Windows, you can follow the below steps to unhide them and access the data.

1. If you are able to read the hard drive, I suggest you to navigate to the drive partition and
   
   unhide all the hidden folder and check.
   
2. If you are still not able to see the data, uncheck
   Hide protected operating system files.
   
3. After you have found your files, I suggest you to undo the changes.
   

If you still face the issue, reply to this post with more information.

Hope it helps.

Amit Sunar

Microsoft Community – Moderator