Windows 10: What is the solution to stop the blue screen of death loop.

I shutted down my laptop and turned it on after a few hours and it began to show the blue screen which displays " Your device ran into a problem and needs to restart and we will restart for you ". And it has begun to start the device and goes to same blue page and keeps repeating the same message again and again. And I inserted an bootable pen drive which has windows 10 file and reset the C drive so that i can do a clean installation of new windows but even after resetting the C drive the same blue screen appears and displays the same message And I also deleted the recovery files which holded

:)

 

Blue screen of death issue

Hi Malcolm,

Blue screen of death error can be caused either by hardware failure or software compatibility. To help you resolve the blue screen of death issue, we would like to get more information:

• Please provide the complete stop error message that you are getting.
• Were there any changes made prior to the issue?

We recommend following the troubleshooting steps in the article:
Troubleshoot blue screen errors

Should you need further help, you're always welcome to post back.

 

Getting blue screen of death loop

Windows 10 blue screen loop is an error that usually occurs when you are stuck in a Blue Screen of death reboot loop. It can be caused by a Windows Update, a device driver update or a recently installed hardware.

Please see our in-depth walk-through solutions below.

1. Uninstall corrupt driver

“Windows 10 blue screen loop” could be due to a newly installed driver. You may want to uninstall it using safe mode. Please see below to access safe mode.

2. Test Hardware

“Windows 10 blue screen loop” may also be due to faulty, semi-detached or dusty hardware. You may want to check the hardware one by one. If you recently installed new hardware, it could be the cause. Remove it and test.

3. Fix Master Boot Record (MBR) and Registry

“Windows 10 blue screen loop” may also occur due to a corrupt or missing registry. It may be caused by a conflict driver, accidentally changed or deleted registry or a third-party software malfunction.

4. Use Advance Option

“Windows 10 blue screen loop” may also occur if your Windows 10 has recently undergone Windows update that may not be compatible with the current hardware or drive which result to the blue screen of death loop. It could also be caused by a corrupt Windows update that is recently installed. Uninstalling Windows update or Reset Windows using the Advance Option may fix the looping problem.

5. Reinstall Windows

If all the components are in good condition, “Windows 10 blue screen loop,” could be caused by your Windows, which is unfixable. Reinstalling Windows may fix the error.

 

Blue screen and stop code

Hi
Jeferis,

There are a lot of factors for this matter to occur. To isolate the issue, we have some questions for you:

• 
  What activity have you done to
  trigger the NTFS and FAT FILE SYS loop?
  
• 
  were there any error messages?
  
• 
  What troubleshooting steps have you done so far?
  

It is possible that the
Boot
Sequence were corrupted by the previous activity which
triggered the Blue Screen Error and the loop. We recommend that you perform these
suggested troubleshooting
and see if there are any changes:

Startup Repair.


To access the
Startup Repair Screen, turn off the
PC 3-4 times(force shutdown),
while on the Blue screen Error. This will route you to the
Startup repair screen:

Advanced Boot Options > click Troubleshoot > Advanced options > Command Prompt

and run the following command:

Run SFC Scan:  

SFC
will
scan
and
run
an
automatic repair
to any
corrupted system files
that it will detect. We suggest that you perform it twice. To run an
SFC scan, follow these steps:  

• 
  Run
  Command Prompt as Administrator.  
  
• 
  Type
  sfc /scannow
  and hit
  Enter.   
  

Boot Record:

This will fix the corruptions on
boot records or boot
sequence. To run this command, follow these steps:

• 
  Run
  Command Prompt as Administrator.
  
• 
  Type the following command:  
  
  • 
    Bootrec /fixMBR  
    
  • 
    Bootrec /fixBoot
    
  • 
    Bootrec /rebuildBCD
    

Update us on how it goes.

Regards.