Windows 10: When I start up I get an error message saying my keyboard has errors and then it won’t...

When I start up I get an error message saying my keyboard has errors and then it won’t write so I can’t type my code to open the computer

:)

 

Error Message when updating from Win-7 to Won-10

Bree
I followed your suggestions (2nd Aug 19) for installing Win-10. Made the bootable flash drive successfully through the media creation tool. But when I attempted to upgrade and activate to Win-10 (64 bit) from within Win-7 (Pro-32 bit), I got the following error message:

Error # OxC1900101-Ox20017. " The installation failed in the SAFE_OS phase with an error during BOOT operation"

I read the diagnostics under this error number and carried out the proposed fixes, i.e. update Win-7, uninstall Malwarebyte antivirus, disconnect all external hardware, e.g. printer, scanner, external hard drives. I then tried to repeat the steps to do the upgrade through the Win-10 bootable flash drive as before. Got the same error message.
Appreciate any further comments and suggestions as to (a) what does a failure in the SAFE_OS during boot operation mean, (b) what can I do to solve it. Is this anything to do with the hardware in my computer? I listed these in my first posting above.
Thanks for any help

 

usb keyboard giving bios errors at boot

bios ver 0402 x64
2 usb 2 ports (i will name A and B for convinience of explanation) next to ps/2 port,this is where keyboard and mouse have always been plugged.
error message appears after asus logo and reads "keyboard not detected"
bios has not been updated no settings have ever been altered with exception of case fan controll and enabling ram xmp profile
bios set to fast boot and legacy usb enabled
desktop is used for gaming mainly and is used about 4 times a week and no faults of this nature have been experienced in the past

got the error message 2 days ago
Case 1 : keyboard in A and mouse in B
-four starts and error message is produced in 3 and windows boots normally on all starts with both devices usable at login screen and desktop environment
-three starts to check devices in bios,can use keyboard to enter bios and both devices usable and recognised (1 keyboard,1 mouse usb config under advanced settings)in bios

Case 2 : keyboard in B mouse in A
-four starts and results are similar to case 1 with exception that error message appeared on all starts

Case 3 : no device in either A or B
-error message "no keyboard or mouse detected"

Case 4 : keyboard in A or B, mouse not connected
-error message "no keyboard detected"
-can enter bios and device usable in bios and windows environment
-i couldnt navigate in bios to check listed devices as bios mainly uses the mouse

Case 5 : mouse in either A or B and keyboard in usb 3 port near lan port
-no error message, both devices usable in windows login and dektop environment
-keyboard can enter bios however if the pc is cold booted(psu turned off and on before pc power switch turned on) usb cannot be used inside bios,though if i continue to windows and reboot it is completely functional regardless of number of restarts

now i have no idea what to make of results in case 4 because that would mean the the keyboard was being identified as mouse
also in case 1 keyboard did boot once with no errors so maybe the keyboard is malfunctioning but it cold start doing the same in usb 3 later or does it have a problem with usb 2
i hoped i could get insight before i get a new keyboard or change bios settings or flash it
its my first build, i dont want to break anything with haste (this stuff is expensive as ....!!!) and i only have a samsung np550pc to fallback on (i cant game on that once again)

 

Can't share printer—getting error message

Step 1: Go to store.
Step 2: Buy a less shitty printer.
Step 3: Pick up some beer while you are there.
Step 4: Enjoy both your new printer and your beer.

In all seriousness, I have had more issues with Lexmark printers and their shitty drivers then any other manufacturer, HP is a close second though.

However, if you don't want to get a new printer*Laugh :laugh:, and I can understand that, when my Lexmark was giving me the same troubles in Win7(and Vista) I had to make sure the Windows firewall was ON and the firewall service was enabled and running. After I shared it I could re-disable the firewall and firewall services.