Windows 10: Why does when my computer start it says it is checking and scanning drive and repairing it...

So I had a problem when I started my PC it started to say scanning and repairing disk and it said that every time but it never worked. So I tried to scan repair my disk and it said I had problems and so I repaired it but it did but checked again it said that same message again. So I tried going to Command Prompt checking and repairing the drive like that. We tried everything and it didn't not work, So there is anything I can do to fix this it would be amazing. Just don't answer with "do a system refresh or deleted all data from drive" here is a screen shot if you don't get it,

:)

 

Scanning and repairing drive on every start-up

Recently, I had a start-up error with the "Reboot and select proper Boot device" message. I fixed it by unplugging and then plugging back in my drives, but since then it has been slow with starting up Windows, attempting to scan and repair an unknown drive before the login screen.

I need help to figure out which disk it is referring to and how to get rid of the scan and repair thing on start-up.

Windows Version Number: 1903 (OS Build 18362.900)

(Link to the previous thread: Scanning and repairing drive on every start-up
Tried the things listed there, but couldn't get much further. Was suggested to start this new thread...)

 

Scanning and repairing drive (C Windows 10

Hi,

Windows 10 may have encountered a system file corruption after it was turned off while it was scanning and repairing drive (C. For us to help you access your computer and end the scanning and repairing loop, we suggest that you perform a startup repair.
Kindly follow the steps below:

• Start your computer from the installation media, Insert the DVD or USB flash drive and restart your computer. Press a key once you see a message that says
  Press any key to boot from DVD.
• On Install the Windows screen, select Repair your computer to the
  Windows Recovery Environment.
• On the Windows Recovery Environment, on the Choose an option screen, select
  Troubleshoot.
• Select Advanced options. Under Advanced options, select
  Startup Repair.
• Startup Repair will now start Diagnosing your PC, and will perform an automatic repair.
  

Meanwhile, if you don't have a disk or USB, download the ISO from a different computer and try creating a bootable disk or USB. Kindly refer to this

link and follow the second option that says Using the tool to create installation media to install Windows 10 on a
different PC.

Please get back to us with the results.

 

acer aspire stuck on Scanning and repairing drive

Hi,

The challenge that you are experiencing when trying to boot up your computer can occur due to several reasons such as corrupted/missing system files, bad sectors on your hard disk, etc. We recommend that you boot your computer in safe mode so that you can
troubleshoot the issue. To do so, kindly follow these steps:

• Start your system.
• After your computer shows its original equipment manufacturer's logo, perform a hard shut down by pressing and holding the power button until your computer shuts down.
• Repeat steps 1 and 2.
• Start your system again. This time, Windows will boot into the Windows 10 Repair Environment.
• Select Troubleshoot.
• Click on Advanced Options.
• Select Startup Settings, then click restart.
• When your computer restarts, press the corresponding key for safe mode to boot your computer in safe mode.

Once you're able to boot into safe mode, kindly run the System File Checker tool and the
Deployment Image Servicing and Management tool. The System File Checker tool
and the Deployment Image Servicing and Management tool check if there are corrupted system files on your computer. If the
System File Checker tool detects incorrect, corrupted, or damaged system files, it replaces them with the correct file versions. If it cannot repair the issue, the
Deployment Image Servicing and Management tool will try to fix as many errors as possible. To run the said tools, kindly follow the steps in this article:

System file check (SFC) Scan and Repair System Files & DISM to fix things SFC cannot. Remember to thoroughly read the instructions.

Also, try checking your local disk for any errors while in safe mode. To do so, follow these steps:

• Launch the File Explorer.
• On the left panel, click on This PC.
• Right-click on your local disk (C:, D:, E:, etc.), then click on Properties.
• Select the Tools tab, then click on Check.
• Click on Scan drive. If errors are found, click on Scan and repair drive, then follow the on-screen instructions to repair your disk. Once done, check if the issue persists.

Kindly get back to us once you've tried the steps that we have provided.