Windows 10: WiFi adapter problems

Hello everybody,


Over the past month I come experimenting problems with my connection which i didn't know whether they were my fault or mi ISP's, but came to discover today it was indeed mine.


When the WiFi connection went away I tried to reset TCP/IP configuration, checked if DHCP protocol was working, and many things that I will list down here:


-netst winsock reset catalog

-netsh int ip reset

-ipconfig:

-/release: "An error occurred while releasing interface Wi-Fi : An address has not yet been associated with the network endpoint."

-/renew: Here I always get an error displaying that the waiting time ended for the DHCP connection

-Disable/Uninstall adapter's drivers

- Disable IPv6 config on adapter

I can't manage to find where the problem was so I would really appreciate any help nyou guys could give me.

Thanks in advance to everyone.

:)

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?

 

Wifi and browser problems with windows 10


I'll tell you how I fixed an identical problem on a ASUS laptop that had run perfectly on Windows 7 and ran well on W10 from January until the Anniversary update in early August. I tried everything I found on this forum and two others. Nothing worked. The last thing someone suggested was disabling the adapter and using a WiFi dongle. Problem continued. Nobody suggested changing the wireless network adapter. I bought and installed an Intel 7260 WiFi card and just used the driver which was downloaded on the reboot after the install. All problems solved!!

I must have wasted two months reading and trying everything. Even the manufacturer support inferred I needed a new machine though they sent me a Windows 8.1 driver to try, with the same result.

I'd suggest contacting the manufacturer to determine if they white list any cards and see if they have suggestions for a compatible card. They may want you to buy another laptop but if the cards aren't white listed, a simple card swap to one compatible with Windows 10 seems to be the answer.

 

Wifi adapter disappears - goes 'hidden'


Running Windows 10 on an Acer laptop. Over the past month, the wifi connection dropped without explanation/warning.

First time, the adapter was visible in Device Manager (with a yellow triangle next to it). An interent search found the suggestion to uninstall it and restart. That worked.

Today, the connection dropped again. In Device Manager at first I could not see the wifi adapter listed. I clicked to see hidden devices and found the adapter and the Bluetooth (which I had not noticed was missing).

I again uninstalled, restarted, and both the wifi and bluetooth have returned.

Anyone any ideas as to what is happening, why it's happening, and what I need to do, please?

I have attached a screenshot of the DM windows as it is now, showing the wifi adapter name, etc.

Thanks very much

WG