Windows 10: Will disabling secure boot solve my windows 10 2004 update problem 0xc1900101 and...

Lenovo Ideacentre 310s-08asr amd a9-9245 radeon r5 compute cores 2c+3G

8Gb Memory

879Gb free on hard drive

Razer Chroma keyboard

Windows Defender used no 3rd party

Have tried all the below and every occasion I get error 0xc1900101 or 0xc1900101-0x20017 when media creation tool is used

Have installed windows 10 to a bootable usb device 16gb

bios set so that usb is primary boot device over hard drive

Reset computer

screen momentarily shows windows logo then there is a flicker and the normal lenovo boot screen is displayed

then computer tried the usb again and the same flicker and back to the lenovo screen again

computer keeps this loop going until the usb is removed and computer then boot normally.


Previously tried windows update to no avail constantly getting error 0xc1900101 but using windows media creation tool I get error 0xc1900101-0x20017. I have installed build 2004 on my 5 year old HP and 7 year old HP laptop both times on the first occasion.

I am wondering now if I it could be the secure boot in the BIOS that could be the problem.


Have run lenovo vantage and it reports system up to date

Have run lenovo system update and it updated the AMD onboard graphics driver, that reported no other updates are required.

Ran the AMD drivers and supported and that updated drivers and AMD software

System has Office, Canon drivers and software for TS8351 installed, Google Earth, Firefox, Chrome, Thunderbird and IMVU installed.

The computer has been taken back to 1903 its original format and even with nothing added resulted in error 0xc1900101 and 0xc1900101-20017 using media creation tool. The system has successfully updated to 1909.

Update troubleshooter this time reports an issue has been detected. When you look at the details it says "check for windows update issues"

Then says "resolve windows update issues - completed

Then WaaSMedicService

Issues remediated by: EnableUUPScanPlugin.

Then detection details

IsPostback_RCUpdates : IsPostback: False

WaaSMedicService: Issue found by: EnableUUPScanPlugin

IsPostback_RC_PendingUpdates: IsPostback: True

Service Status

Problem with BITS service: The requested service has been started. More help is available by typing NET HELPMSG 2182

BITS troubleshooter reports that it cannot find a problem

Have tried a clean install but computer did not boot from usb, found out boot order in BIOS had to be changed so made usb number 1 in priorty

Then tried the clean install again and although the computer tried to boot from usb I got the windows symbol but then before startup could start I get a "flicker" and then the computer tries to boot from the hard drive before trying the usb and so on in a loop. Removal of usb and the computer boots as normal.

I even tried to update from recovery to 1903 to 2004 via media creation tool and that failed but did not give an error, here I used the "download tool now" option, then chose to "upgrade this pc now". When the windows update assistant downloaded is run I am told that the computer is compatable.

The install starts does everything it should but on restart the computer tries to load windows again and again before I am dumped to the lock screen after at least 8 minutes and back to 1909.

It seems having watched a video on You Tube that I need to change in BIOS that secure boot was on and to change that to off. I was wondering if the secure boot being on could be part of the update problem?

Have tried Lenovo support but they insist that "this is out of our support scope."

Was asked to look at https://support.microsoft.com/en-us/windows/get-help-with-windows-10-upgrade-and-installation-errors-ea144c24-513d-a60e-40df-31ff78b3158a

Responded:


Checked that

1 Hd has 879Gb Free

2 Windows update has been run multiple times

3 No third party drivers are installed other than for the mouse, keyboard and printer. These proved no problem when updating my 5 year old HP computer to build 2004

4 No external hardware is attached other that razer keyboard, mouse and canon printer via wifi

5 Device Manager is reporting no faults

6 I am using windows defender, mcaffee was installed but that was uninstalled weeks ago

7 chkdsk c: reports no problems, no bad sectors or anything else

8 Performed a clean boot several times to no affect

9 dism.exe still failed


All this has been performed before. Even tried a clean install of windows but that failed because the computer got stuck in a loop trying to start the windows install program and a normal windows boot.


So the question is, is the secure boot being enabled in BIOS preventing the windows update to 2004?

:)

 

Windows 10 Update

Well just noticed a pretty large one pop up coming in at 914MB, seems it makes some pretty serous updates.

KB3172985
https://support.microsoft.com/en-us/kb/3172985

This security update includes improvements and fixes in the functionality of Windows 10 Version 1511 and Windows Server 2016 Technical Preview 4. It also resolves the following vulnerabilities in Windows:

• 3175677 MS16-094: Security update for secure boot: July 12, 2016
• 3174060 MS16-093: Security update for Adobe Flash Player: July 12, 2016
• 3171910 MS16-092: Security update for Windows Kernel: July 12, 2016
• 3170048 MS16-091: Security update for .Net Framework: July 12, 2016
• 3171481 MS16-090: Security update for Kernel Mode Drivers: July 12, 2016
• 3170050 MS16-089: Security update for Windows secure kernel mode: July 12, 2016
• 3170005 MS16-087: Security update for the Microsoft Print Spooler: July 12, 2016
• 3169999 MS16-085: Cumulative security update for Microsoft Edge: July 12, 2016
• 3169991 MS16-084: Cumulative security update for Internet Explorer: July 12, 2016

 

Cannot Disable Secure Boot

Yes, I am following the steps there exactly.

The person in this thread (https://www.dell.com/community/Alie...ure-Boot-on-Aurora-R5-Windows-10/td-p/5629825) seems to be having the same problem as me, but there are no working solutions on that thread.

EDIT: I managed to solve it.

You can boot into windows without Secure Boot by disabling the option under it, forgot what it was but it was something about Legacy something something.

 

Error 0xc1900101 0x40017 when updating to 2004

Hi, I am trying to update my windows 10 pro from 1909 to 2004. I tried already 3 times, the first twos with windows update and the latest with the iso. However they end with the same result with the error 0xc1900101 - 0x40017 "the installation failed in
the second_boot phase with an error during boot operation".

I found this page https://docs.microsoft.com/en-us/windows/deployment/upgrade/resolution-procedures but I don't have Citrix VDA
installed (I don't know even what is its purpose) so I can't follow the solution steps.

Has anyone got any suggestion? Aside for a clean install. Thank you