Windows 10: windows 10 recovery usb drive

I have a dell 5290 2in 1 laptop, it showed a error message of 0xc000000f

* I Downloaded windows 10 from a different computer to a USB stick

* i then put the usb into the dell computer

it went into recovery mode for about 20 minutes then said

there was a probelm and no changes were made,


I NEED TO DOWNLOAD WINDOWS 10 ONTO THIS COMPUTER WITH ERROR MESSAGE, I HAVE IT IN UEFI MODE AND BOOT PATH SECURITY IS ON ALWAYS , EXCEPT FOR HDD


WHY WONT IT FIX THE COMPUTER

:)

 

Recovery Drive for Windows 10 Doesn't Recognize USB Drive

When I try to create a Recovery Drive in Windows 10, Windows doesn't recognize the flash drive.

I'm following the instructions to create a Recovery Drive listed here:

http://windows.microsoft.com/en-us/windows-10/create-a-recovery-drive

• 
  From the taskbar, search for Create a recovery drive and then select it. You might be asked to enter an admin password or confirm your choice. (I was asked to confirm my choice, and I clicked "Yes".)
  
• 
  When the tool opens, make sure Back up system files to the recovery drive is selected and then select
  Next.
  
• 
  (Secret Step) Wait a minute or so for the "Please Wait" screen to finish thinking
  
• 
  Connect a USB drive to your PC, select it ...
  

The issue is that when I connect a USB drive to the PC, it doesn't appear on the "Connect a USB flash drive" screen as a drive that can be selected, and the "Next" button is grayed out.

However, when I look in File Explorer, I can see the USB drive plugged into the computer. Selecting Properties shows that Windows considers its Type to be "Removable Disk". (Sounds right to me.)

I'm not getting any error messages.

My environment:

A brand new Toshiba Sattelite C55-C5241 laptop with Windows 10 Home. It's never had anything other than Windows 10 on it - unless they upgraded it at the factory.

A brand new ativa 8GB USB flash drive. Note that the packaging for the USB drive does not include Windows 10 in the System Requirements, but seriously?

What I've tried:

• Plugging the flash drive into all three USB ports (USB 2, USB 2, and USB 3)
• Reformatting the flash drive with FAT32
• Restarting the computer with the flash drive plugged in
• Turning off Real-Time Scanning in McAffee

I've seen a few threads with this issue in Windows 8, but none of the potential solutions in those threads have worked for me. So here I am asking the same question, but for Windows 10.

Does anyone have any suggestions for resolving this issue?

Thank you.

 

Windows 10 recovery USB - which size???

Not even that. What creating a recovery drive does (if you select 'include system files') is to construct the files required to clean install Windows. If this is made on an OEM install these file will include the OEM custom apps and drivers - effectively a 'factory reset' drive. It is extracting an install image from your existing system files that takes the time.

The steps in making a recovery drive are shown in this tutorial...

Create Recovery Drive in Windows 10 | Tutorials

• first you choose whether or not to include system files (step 5 in tutorial)
• next the recovery drive files are constructed (this can take a long time if you include system files)
• only after that is complete will you be asked which usb to use (step 6 in tutorial). At this point you will be told how large a usb you need.

Without system files 512 Mb is sufficient. Including system files it will be just over 4GB.

At which step did you get the error? If you were not asked which usb to use then it was the construction of the system files that failed, nothing to do with what usb you had.

 

Is it time for Windows 10 already?

Here's a good step by step guide on doing a fresh install.

How to clean install Windows 10 from a USB drive - Software - Feature - HEXUS.net