Windows 10: windows 10 update 2004 error 0xc1900101 and 0xc1900101 and bootable windows 10 usb will not...

Have rest the computer yet again for the umpteenth time

Have had one advisor on here saying my pc might not be compatable but it is only 1 year old

Lenovo Ideacentre 310s-08asr amd a9-9245 radeon r5 compute cores 2c+3G

8Gb Memory

875Gb free on hard drive

Razer Chroma keyboard

Windows Defender used no 3rd party

Have used Lenovo Vantage and system is up to date

Have tried using Lenovo support site using the automatic driver update and that reports - no drivers required

Every attempt to install end with error 0xc1900101

When using media creation tool I get 0xc1900101-0x20017

System configures update, but when it tried to reboot. It goes into a loop before for about 8-10 minutes before i'm returned to the lockscreen and back to version 1909.

Have run lenovo vantage and it reports system up to date

Have run lenovo system update and it updated the AMD onboard graphics driver, that reported no other updates are required.

Have not used 2 USB devices and windows media tool to create bootable drive, have moved usb so that it is first in priority

On restart computer tries to enter windows startup but flickers then tries to boot from hard drive and to go and fro between the 2 until the usb is removed and computer then boots as normal.

Ran the AMD drivers and supported and that updated drivers and AMD software

System has Office, Canon drivers and software for TS8351 installed, Google Earth, Firefox, Chrome, Thunderbird and IMVU installed. These proved not to be a problem as my 5 year old HP computer updated to 2004 without any problems.

Tried again and error 0xc1900101 occurred yet again.

The computer has been taken back to 1903 its original format and even with nothing added resulted in error 0xc1900101 and 0xc1900101-20017 using media creation tool.

Update troubleshooter this time reports an issue has been detected. When you look at the details it says "check for windows update issues"

Then says "resolve windows update issues - completed

Then WaaSMedicService

Issues remediated by: EnableUUPScanPlugin.

Then detection details

IsPostback_RCUpdates : IsPostback: False

WaaSMedicService: Issue found by: EnableUUPScanPlugin

IsPostback_RC_PendingUpdates: IsPostback: True

Service Status

Problem with BITS service: The requested service has been started. More help is available by typing NET HELPMSG 2182

:)

 

Windows 10 Update Error 0xC1900101 - 0x40017

Hi,

Thank you for posting in Microsoft Community, we appreciate your interest in Windows 10.

I understand your concern with the error: 0xC1900101 - 0x40017 while upgrading to Windows 10, we will help you with this issue.

I would like to inform that this error may occur for one of the following reasons:

• Antivirus software conflicts
• Hardware conflicts
• Corrupted/ faulty driver conflicts

I suggest you to refer to the below article by Andre Da Costa, try the troubleshooting steps mentioned under:
0xC1900101 - 0x40017 error code and check if it helps.

How to: Troubleshoot common Setup and Stop Errors during Windows 10 Installation

Hope it helps. Reply to the post with an updated status of this issue for further assistance.

 

Unable to upgrade one of the system to Windows 10 Update Error 0xC1900101 - 0x20004

Thank you for the reply. I read both of those threads already.

1. Resetting BIOS. I flashed BIOS to the latest version. Currently running default settings. No change.

2. Andre da Costa brings up a list of reasons. For error 0xC1900101-0x20017 he says refer to error 0xc000021a.

2a. Regarding his troubleshooting steps for error 0xc000021a. He says to wipe the drive and switch from NTFS to GPT. This is incorrect. If this was true, then no one could update from Windows 7 to Windows 10 without a clean install. Beyond which, I updated
my first desktop from Windows 7 to Windows 10 when it was running Windows 7 on NTFS.

2b. Regarding his additional troubleshooting steps for error 0xC1900101-0x20017. He has a number of suggestions, such as disabling peripherals. I tried all of these for both .iso and USB installs. No luck.

Any other suggestions?

 

Multi-bootable USB

Hey guys from TPU, couldn't find any specific thread pertaining to the question asked on title. As mentioned, I'm trying to create a bootable USB, but with many specifics boots available.

I've been trying to create one with multiple boot device including one that enables me to run Windows 10 directly on the USB Thumb Drive but to no avail.

The list of bootable images i'm trying to create are

1. Windows 10 (A full OS running from thumb drive)
2. Windows 10 ISO (Bootable disk image for fresh install)
3. MemTest86+

Have tried YUMI or UUI from the website USB PenDrive Linux but as this is my first time, i don't know how am i screwing up or am doing it right.. Anyone got a rough idea on a step by step guide? Thanks!