Windows 10: Windows 11 update KB5034123 fails to update at step of restarting computer

Hi, so I can't fully install Windows 11 update KB5034123. It's downloading, it's installing sucesfully in windows update, but when I'm restarting computer to finish instalation of update, at some point it fails and shows information `"Something went wrong, no need to worry, undoing changes"`, then it's trying like 3 times to install it but still fails and then system just boot normally without this update and it's downloading and installing again in windows update.I tried already pretty every solution I found on microsoft forums etc. for problem like this, so for example reseting windows updat

:)

 

Windows Updates failed to instal

I just did step one and they have just all installed.... thank you so much.... it was quite frustrating having that update window pop up every 5 minutes and failing to instal every time

Thanks mate

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.

 

Windows Update keeps failing!

Hi,

I had once a similar issue like yours, i.e. not able to update Windows 7. What I did to solve the problems is:

- go to control panel, then to "Troubleshouting" > "System and Security" > "Fix problems with Windows update" > click "Advanced" > choose "Apply repairs automatically".

And Windows will start detecting the issues and will repair "Windows update components". The problems should be fixed now, close the program, restart the PC, and see if the mentioned steps have fixed the problems you mentioned.

Hope it works for you.

Good luck!