Windows 10: Windows Updates and Driver Updates Failing

For the past week or so, I have been unable to install Windows Updates. I have also been unable to update any of my drivers. When I attempt to, I receive an error code 0x800703f1 for the Cumulative Windows Update, and a 0x800703e3 error code for the Driver Updates.


As for manually updating the drivers via Device Manager, I get an error saying that "The configuration registry database is corrupt.". Seeing this, I looked it up and was taught how to enter Command Prompt and to perform a "sfc/scannow". I performed this Command multiple times, and it finishes successfully and says that it has found and fixed corrupt files. Despite this, when I tried to do Windows Update again, or manually update my Drivers, the same errors that were aforementioned occur.


Looking further into it, I have also been taught how to use the Media Creation Tool to update and upgrade Windows through it. However, when I attempted to do this (multiple times) it would stop at around 57% and fail every time. I have even attempted to Reset my PC via the Recovery tab in Settings but this process would also fail.


I am at quite a loss and it feels as if the only solution is to do a clean reinstall of Windows 10. I would like to avoid this as I do not have any external storage on hand and would like to avoid the hassle. Any help is much appreciated.

:)

 

Windows Updates failed to instal

I just did step one and they have just all installed.... thank you so much.... it was quite frustrating having that update window pop up every 5 minutes and failing to instal every time

Thanks mate

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.

 

Windows update failing

You could try the Windows Update troubleshooter. http://windows.microsoft.com/en-us/windows7/open-the-windows-update-troubleshooter

If that doesn't work then do this: