Windows 10: Computer Crashing Once Per Day

I recently upgraded my computer. I ran Windows off the old SSD and everything was working well. I then purchased a Western Digital SN550 Blue 1TB NVMe SSD and installed windows, I have a MSI B450I motherboard Micro ITXand a AMD 3600 processor. Ever since then I have had BSODs once per day. It normally happens when I watch You Tube or start up a game. Once it crashes and reboots, it doesn't happpen for the rest of the day. Once i shut down my computer the next day when I am watching a video or start up a game it crashes again.


The main errors I keep getting are listed below. I have tested the memory multiple times, updated my drivers, and removed all programs I do not use. I'm out of ideas, thanks in advance. I have also turned off fast startup.



On Wed 7/8/2020 12:14:42 PM your computer crashed or a problem was reported
crash dump file: C:\WINDOWS\MEMORY.DMP
This was probably caused by the following module: ntkrnlmp.exe nt!memset+0x44BAB
Bugcheck code: 0x1E 0xFFFFFFFFC0000005, 0xFFFFF80637245A6B, 0x0, 0xFFFFFFFFFFFFFFFF
Error: KMODE_EXCEPTION_NOT_HANDLED
Bug check description: This indicates that a kernel-mode program generated an exception which the error handler did not catch.
This might be a case of memory corruption. This may be because of a hardware issue such as faulty RAM, overheating thermal issue or because of a buggy driver.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Tue 7/7/2020 12:32:58 PM your computer crashed or a problem was reported
crash dump file: C:\WINDOWS\Minidump\070720-12593-01.dmp
This was probably caused by the following module: ntoskrnl.exe nt+0x1C23A0
Bugcheck code: 0x3B 0xC0000005, 0xFFFFF80771FC972F, 0xFFFFAD817B17F930, 0x0
Error: SYSTEM_SERVICE_EXCEPTION
file path: C:\WINDOWS\system32\ntoskrnl.exe
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This indicates that an exception happened while executing a routine that transitions from non-privileged code to privileged code.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.



On Mon 7/6/2020 11:59:25 AM your computer crashed or a problem was reported
crash dump file: C:\WINDOWS\Minidump\070620-12125-01.dmp
This was probably caused by the following module: classpnp.sys 0xFFFFF8006BCF8A10
Bugcheck code: 0x1E 0xFFFFFFFFC0000005, 0xFFFFF8006BCF8A10, 0x1, 0x2
Error: KMODE_EXCEPTION_NOT_HANDLED
file path: C:\WINDOWS\system32\drivers\classpnp.sys
product: Microsoft® Windows® Operating System
company: Microsoft Corporation
description: SCSI Class System Dll
Bug check description: This indicates that a kernel-mode program generated an exception which the error handler did not catch.
This might be a case of memory corruption. This may be because of a hardware issue such as faulty RAM, overheating thermal issue or because of a buggy driver.
The crash took place in a Microsoft module. Your system configuration may be incorrect. Possibly this problem is caused by another driver on your system that cannot be identified at this time.

:)

 

all games crash!

I suggest you run rthdribl > http://www.daionet.gr.jp/~masa/archives/rthdribl_1_2.zip
Increase the window size step by step and watch your vga temps permanently.
What happens?
If it crashes, run at stock speeds as suggested before and retry.

P.S.: When your system locks, does the display signal turn off after a time?
Stuttering sound or no sound at all when freezing?
What X1800XT model do you own exactly?

 

N97 is restarting by himself once or twice per day

My N97 is restarting by himself once or twice per day, on an interval of 2-3 days, sometimes when I do something on it, sometimes when it stays on the desk, it is very annoying!

This thing it will fix if I go on service (Nokia service) and I reinstall the soft?

Has anybody has this issue?



P.S. I have last firmweare on it (V12....)



10x a lot

 

My computer blue screens and crashes at least once a day

Hi,

Thank you for choosing Microsoft Community Forums.

I understand the inconvenience you are going through and I regrets the same.

I would suggest you to try these methods and check if that helps:

Method 1:

Perform a clean boot.

A clean boot is performed to start Windows by using a minimal set of drivers and startup programs. This helps eliminate software conflicts that occur when you install a program or an update or when you run a program in Windows 10,
Windows 8.1, Windows 8, Windows 7, or Windows Vista. You may also troubleshoot or determine what conflict is causing the problem by performing a clean boot.

Note:

• 
  You must log on to the computer as an administrator to be able to perform a clean boot.
  
• 
  Your computer may temporarily lose some functionality when you perform a clean boot. When you start the computer normally, the functionality returns. However, you may receive the original error message, or
  experience the original behavior if the problem still exists.
  
• 
  If the computer is connected to a network, network policy settings may prevent you from following these steps. We strongly recommend that you do not use the System Configuration utility to change the advanced
  boot options on the computer unless a Microsoft support engineer directs you to do this. Doing this may make the computer unusable.
  
  I suggest you to try the steps provided, in the link below in order to perform a clean boot on your computer.
  
  https://support.microsoft.com/en-us/kb/929135
  

Method 2:

• Open the Task manager. Here’s a tip: Press CTRL+Shift+ESC.
  
• Click File > Run New Task
• Make sure you have a check mark beside “Create this task with administrative privileges”
  
• Type CMD
• Type the following 4 commands at the Command Prompt:
  
  dism /online /cleanup-image /restorehealth
  
  sfc /scannow
  
  powershell
  
  Get-AppXPackage -AllUsers |Where-Object {$_.InstallLocation -like "*SystemApps*"} | Foreach {Add-AppxPackage -DisableDevelopmentMode -Register "$($_.InstallLocation)\AppXManifest.xml"}
  
• Close the CMD window.
• Check to see if the issue is resolved. If not, restart the PC.
  

I hope it helps. If you have any issues regarding Windows in future please let us know. We will be happy to help you.

Thank you.