Windows 10: Script to add a rule for Routing and Remote Access

• From Firewall I want to add a rule - Routing and Remote Access.
  This rule can be added manually, but I want to add it from the command prompt.
  I am using Windows 10 Pro 20H2.
  To add manualy, open Control Panel -> Windows Defender Firewall -> Advanced Settings ->
  -> Inbound Rules or Outbound Rules -> New Rule -> Predefined -> from drop down list choose Routing and Remote Access ->
  -> Next -> Check all checkbox
  Routing and Remote Access (PPTP-In),
  Routing and Remote Access (L2TP-In),
  Routing and Remote Access (GRE-In) -> Next... Next - see print screen.
  How to add from CMD ?
  
  

:)

 

Cannot Start the Routing and Remote Access Service

I get the error below and the event below logged when I try to start the RRAS service. Any ideas?

 

Remote Access

1. Follow these steps to disallow remote access to your PC completely:
2. 1. Type “remote settings” into the Cortana search box. Select “Allow remote access to your computer”. This may seem counter-intuitive, but this opens the Control panel
   dialog for Remote System Properties.
3. 2. Check “Don't Allow Remote Connections” to this Computer. You've now disabled remote access to your computer.

Try these two steps and tell us if your issue gets solved. If it does not then your PC may be infected. Use a Good antivirus to remove the infection from your device completely.

 

Route to the remote station with win route table

Hello,

I have three pc's:
- Local PC with an ip 192.168.1.100
- Remote PC_1 with an ip 192.168.2.100
- Remote PC_2 with an ip 192.168.2.101
I would like to access remote pc_2 via remote pc_1. On the local pc and remote pc_1 i have enabled routing in the registry. Windows ip configuration shows as follow:
Windows IP Configuration

Host Name . . . . . . . . . . . . : (PC name)
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : Yes
WINS Proxy Enabled. . . . . . . . : No
I have installed teamviewer on local pc and remote pc_1 and a vpn adapters of the teamviewer and established vpn connection betwean local pc and remote pc_1.
On the local pc i have added a route to the route table:
route add 192.168.2.0 MASK 255.255.255.0 (ip of the teamviewer vpn of the remote pc)
Route was added successfully, i have route in the route table:
Active Routes:
Network Destination Netmask Gateway Interface Metric
192.168.6.0 255.255.255.0 (remote vpn ip) (local vpn ip) 56
Now from the local pc i can ping to the address 192.168.2.100:
C:\Windows\system32>ping 192.168.6.253

Pinging 192.168.2.100 with 32 bytes of data:
Reply from 192.168.2.100: bytes=32 time=238ms TTL=128
Reply from 192.168.2.100: bytes=32 time=107ms TTL=128
Reply from 192.168.2.100: bytes=32 time=123ms TTL=128
Reply from 192.168.2.100: bytes=32 time=108ms TTL=128

Ping statistics for 192.168.2.100:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 107ms, Maximum = 238ms, Average = 144ms
I can also ping succesfully from the remote pc_1 to the remote pc_2, but when i try to ping from local pc to remote pc_2 - all packets are lost. Any help is highly appreaciated.
Local pc is Windows 10 pro 1909 OS ver 19363.628. Firewalls, antivirus were temporary disabled while i did tests.