Windows 10: Another Windows Update Problem

Greetings everyone, I thank all of you in advance for reading this. I am deperate at this point

So here I am, with my Windows 1607 build, I know pretty old. And I am finally trying to update, but my built in Windows Updater is not working. It just says "Downloading Updates 0%) and it does nothing.

Now I learned that I can update with the "Windows Update Assistant" and that's what I am trying right now. But after downloading all files (Wich had the most usage on any of my Hardware) It goes from Hyperdrive to Snailspeed. The software sometimes not even touching the disk or cpu. Absolutely no Usage. And when it does it uses the disk for a sum total of 0.1 MB/s and the cpu doesn't even flinch. Up until to ca 50% of the updating it goes fast, but then it changes into snailmode. It does jump up by one percent every now and then, but its maybe once every 2 hours....

So there is my question: Is that normal? If not, can I "Manually" install the update by finding the downloaded files on my computer? Am I just plain stupid and did something wrong?

submitted by /u/Albert_Leary
[link] [comments]

:)

 

Windows Updated(16299.309).KB4088776 Restart is required to complete.


Hi dalchina. Good news, I followed your suggestion and reinstalled the update and now it appears as "installed correctly" *Biggrin Maybe it was not necessary to run the Windows Update Troubleshooter or maybe if necessary. But using it I do not think it could have worsened something. The installation was very fast, unlike the first time it showed step 1 and step 2 completed.

Thanks for the suggestions and for the time to respond Best regards.


And thanks for the tip of that program, I'll have it on my list.

 

Windows 10 1709 System Restore problems...


That seems to be an attempt at Option 2 in the tutorial, which requires you to
a. Boot to a command prompt (Did you?)
b. You then seem to be mixing steps 3,4 and 5, thus your command is incorrect.

I suggest Option 1 is easier.

If you still have problems, please repost listing each specific step and saying which option from the tutorial you are using. Thanks.

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.