Windows 10: Backup Errors

Consistently get the following after each automatic backup:


Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\OneDrive. Error:STATUS_WAIT_2 0x80070002

Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\Pictures\From Chars Windows 10 Phone\Pictures. Error:STATUS_WAIT_3 0x80070003

Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\Pictures\From Pat's Phone. Error:STATUS_WAIT_3 0x80070003

Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\Pictures\From Char's Phone. Error:STATUS_WAIT_3 0x80070003

Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\Documents\Pictures. Error:STATUS_WAIT_3 0x80070003

Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\OneDrive. Error:STATUS_WAIT_2 0x80070002


File locations do not exist in file manager directory when I try to look them up. There is no "C:\Windows\System32\config" location on my hard drive.

Can anyone help me eliminate these error messages?

:)

 

Backup Issue - Microsoft 10 - Get Backup Errors - Third Try Didn't Work

This is my third try for help.

I've enclosed my problem, the steps suggested which I performed, and current status.

My backup stubbornly refuses to run. I can't run the initial backup, therefore the file history backups don't run either. This has been an ongoing problem for quite some time. Suggestions I've received have not worked so far. Following is the problem
and the failed resolution attempts:

• I get this message from the Event Log:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID - 201

Level: Error

User - System

*** ---- There is no config file at this directory location. The contents of the location are:

catalog1

catalog2

config1

config2

• In another thread from July, someone suggested checking a particular service (I forget the name just now) is running. It is.

• Two days ago a Microsoft employee suggested the following steps. These steps resulted in no change, still no backup:

KA

Karthicka_R replied on

• Microsoft
• Support Engineer

Hi,

Thank you for contacting Microsoft community.

I suggest you to follow the below steps to start and stop the services “Windows backup” and “volume shadow copy” and check if it helps.

• Press “Windows+R” and in the run command box type “services. MSc”.
• Search for the service “Windows Backup” double click on it and check whether the service is started or not, click on “OK” button. I suggest you to stop and start the service again.
• Once done again search for the service “Volume shadow copy” double click on it and check whether the service is started or not. I suggest you to stop and start the service again, click on “OK” button and
  check whether you can perform backup successfully.

Hope this information was helpful and do let us know if you need further assistance. We will be glad to assist.

• I performed these steps multiple times. The backup still crashes, with the same error message. In addition I collected the following error message, but only one time:

Unable to start a backup cycle for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 200

• Can anyone help me with this stubborn problem?

Thank you in advance.

You had this question

• 
  
  
  
  

• All replies (1)

DM

Divya M replied on

• Microsoft
• Support Engineer

Hi,

Thank you for posting your query on Microsoft Community.

We sincerely regret for the inconvenience caused.



Method 1Perform a Clean Boot to see if there is any software conflict as clean boot helps in eliminating software conflicts.



Note: After performing the troubleshooting steps in clean boot, follow Step 7 from the link to return the computer toNormal startup mode.



Method 2: Run check disk to check for any errors.



Note: If any bad sectors are found in the hard drive then it might try to repair that particular sector. If you have any data on that, it might be lost.

You may also follow the below link and check if it helps:

Get the latest Windows features | Install Windows 10 Insider Preview



Please let us know if you need further assistance.



Thank you.

-----------------------------------

Yes, I need more assistance.

I ran a disk check on both the source and destination drives for the backup. No errors.

I executed a clean boot. (I have left myself in the clean boot). It doesn't seem to work

I'm not sure to check whether it has worked, and I just couldn't tell. How do I confirm that the initial, image, backup has been completed?

The event viewer reports this error every time I attempt to manually initiate a backup:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 201.

I'm assuming that with this error, my backups are not being done.

 

Backup Issue - Microsoft 10 - Cannot perform initial backup

Question

• 
  
  

Applies to

• Windows
• Windows 10
• Update, backup, & recovery

5 views Backup Issue - Microsoft 10 - Cannot perform initial backup




My backup stubbornly refuses to run. I can't run the initial backup, therefore the file history backups don't run either. This has been an ongoing problem for quite some time. Suggestions I've received have not worked so far. Following is the problem
and the failed resolution attempts:

• I get this message from the Event Log:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID - 201

Level: Error

User - System

*** ---- There is no config file at this directory location. The contents of the location are:

catalog1

catalog2

config1

config2

• In another thread from July, someone suggested checking a particular service (I forget the name just now) is running. It is.

• Two days ago a Microsoft employee suggested the following steps. These steps resulted in no change, still no backup:

KA

Karthicka_R replied on

• Microsoft
• Support Engineer

Hi,

Thank you for contacting Microsoft community.

I suggest you to follow the below steps to start and stop the services “Windows backup” and “volume shadow copy” and check if it helps.

• Press “Windows+R” and in the run command box type “services. MSc”.
• Search for the service “Windows Backup” double click on it and check whether the service is started or not, click on “OK” button. I suggest you to stop and start the service again.
• Once done again search for the service “Volume shadow copy” double click on it and check whether the service is started or not. I suggest you to stop and start the service again, click on “OK” button and
  check whether you can perform backup successfully.

Hope this information was helpful and do let us know if you need further assistance. We will be glad to assist.

• I performed these steps multiple times. The backup still crashes, with the same error message. In addition I collected the following error message, but only one time:

Unable to start a backup cycle for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 200

• Can anyone help me with this stubborn problem?

Thank you in advance.

 

Backup skipped

Hi Ken,

For us to better isolate your concern, we need additional information. Kindly answer the following questions below:

• Are your backing up files or creating a system image?
  
• Are you getting any error messages?
  
• What troubleshooting steps have you done so far?
  

In the meantime, we suggest deleting the backup you created and create a new one. Click this
article
and follow the steps on how to create a backup.

We'll keep an eye out for your response.