Windows 10: BSOD after about 15min for about 4-5 restarts

Hey everyone,

So for the past week i've been getting either the whea_uncorrectable_error or IRQL_not_less_or_equal BSOD... I browsed the forums and did most of the suggestions (mainly updates all my drivers and ran the stress tests, minus the ram).
Updating my drivers seemed to have fixed it for 2 days and this morning i kept getting the errors again.

A little info, I seem to be getting the errors on startup only. About 15min after start up (give or take) I will get a bsod. This will happen about 3-4 times on average and then the computer is fine for the rest of the day... When the restarts happen, i'm either playing some WoW or just on the internet via chrome. I have yet to be able to reproduce the error identically everytime and I will sometimes get the bsod just doing nothing after bootup...

I ran prime95 for 1hour with 0 errors or warning, and ran furmark for 30min with no issues either, I also did a chkdsk and that also gave me no errors for my hdd's.

I'm at a loss atm, not exactly sure what else to check aside from running mem test tonight. Any help would be greatly appreciated

Thanks

:)

 

windows 10 user profile takes forever to load

i get the same issues after updating to win 1o anniversary update. my windows profile takes about 10-15mins to load compared to before around 5 secs. Please address this issue in the next update!

 

win10 16299 crash about every 15min

121417-14234-01.dmp

 

Hi NickDucharme,

Welcome to the 10forums.

In your event logs there are many events about an error detected on Harddisk4 DR4, since you have multiple storage devices & I'm not sure how Windows looks at it to specify which of them is causing this problem I suggest that you test your HDD & SSDs and update the firmware of the SSDs.






Diagnostics Test

HDD TEST


Run SeaTools to check the integrity of your HDD. SeaTools for DOS and Windows - How to Use - Windows 7 Help Forums
Run following tests

• Short Drive Self Test
• Short generic
• Long generic

If the short generic fails, no need for the long generic.


Note Do not run SeaTools on an SSD as the results will be invalid.
Post screenshots/photos of the test results



Run HDTune to

• scan for errors, no quick scan but full scan
• check the health,
• benchmark.

It may take some time, but please take the time you need to perform it properly.
Let me know what the results are

• of the error scan,
• make a screenshot of the health of every hard drive and post the screenshots,
• post screenshots with the benchmark of the
  • transfer rate,
  • access time,
  • burst rate,
  • cpu usage.

Best is to make screenshots/photos of these test results too.

Code: Event[46803]: Log Name: System Source: disk Date: 2016-05-03T17:12:21.198 Event ID: 51 Task: N/A Level: Warning Opcode: N/A Keyword: Classic User: N/A User Name: N/A Computer: Nick-PC Description: An error was detected on device \Device\Harddisk4\DR4 during a paging operation.[/quote]

 

Thank you, I will do the tests as soon as my mem test finishes. I ran some chkdsk before since I am using 2 ssd's and 1 hdd and those came back with no errors. Anything specific I should run for the ssd's aside from chkdsk? Also could it be a usb thats generally always plugged in that could be the cause? since to me that would be the 4th drive

 

You can run HDTune for both the HDD, SSD, SSHD or any other kind of storage drive you can think of (not sure about pluggable storage devices with HDTune though, except if they are extern hard drives) *Smile

That is certainly possible yes.

 

So I completed my mem test, 8 parses with 0 errors. Also completed all the scans with HD Tune, the screenshots are in the compressed file attached.

I tried to run a scan on my usb just for reference, it ran the error scan with 0 errors but after the benchmark it just crashed the benchmark and gave 100% errors after that (screenshot included for the errors)

When it comes to upgrading firmware for the hdd's, i'm not exactly sure what the best method is. I did check with the samsung magician software for firmware updates and the firmware for that hdd is up to date.

 

Install Crucial Storage Executive Client and check the Crucial SSD for firmware updates.

 

Awsome thank you so much, crucial ssd was 2 firmware updates behind so I updated that. Only thing left is the Wester Digital. I found this so far to check its firmware WD Product Update. It says to remove all usb's and rescan but when i do it just doesnt rescan so i'm wondering if only the WD drive has to be connected?

 

My opinion is that HDDs don't really need firmware updating, I've never done any HDD firmware update (neither a SSD firmware update) and my hard drive is fine as it is.

Just let it be for what it is and let me know if another BSOD occurs *Smile

 

Quick update, so far i did not get a BSOD where i normally would so everything seems good. I will keep this open for a few days to make sure its not just a fluke

 

Not a problem *Smile
I hope your system continues being stable.

 

So with windows 10, do you recommend doing upgrades as soon as they come out? or wait a little? I just got some and i'm wondering if i should install them or not considering i was getting BSOD lol

 

The monthly patchday has arrived, it is recommended that you install all provided updates although they should be installed automatically in a matter of time.

 

Alright, so i havent had any more bsod all week so i'm going to mark this as resolved *Smile Thank you so much for the help Axe