Windows 10: Cannot access my router dashboard

SteeldragonMark · Mar 4, 2021

Hi all

I can’t seem to connect to my sky router dashboard on my PC. When I input the IP address in the address bar I get a “hmmmm.... can’t reach this page Err_connection refused” message.

I’m running windows 10 pro.
Version 20H2
Build 19042.804
I also run hyperV on this machine.

I can access it perfectly on my iphone through safari but not on my pc. I run McAfee on both my pc and my phone but even so, I tried turning McAfee off on the pc in case the firewall was blocking access and I still got the same message.

I have tried 3 different browsers. All give the same error.

I can ping the address 192.168.0.1 successfully both by IP address and by domain name.

I have checked the hosts file and I don’t see anything untoward there.

Any ideas? This has got me stumped!

Thanks.

:)

IggSter · Mar 4, 2021

How to factory reset Cisco 1700 Router

Hopefully I can help you here....its a very common thing to happen.

First, I take it you dont know the passwords for console access or telnet/ssh?

I will assume that these devices belong to you.

step 1. Plug a cisco console cable into a serial port on your pc
step 2. Plug other end into Cisco console port
step 3. Using hyperterm or putty or similar connect to the serial port
step 4. boot router, and make sure you clearly can see the output (this confirms you have good serial comms)
step 5. if this fails, adjust the comm port settings (9600, 8,1,n are the default)
step 6. now you have to do the only hard part...send the break command:

Break command list: Break Commands

Go down the list and match your OS and SW and try the sequence suggested.

If this fails several times do what I do: Install putty (free) and then to send a break so you can get into rommom just hit "ctrl-a b".

Mrblack761 · Mar 4, 2021

Unable to access my router

The router's gateway would be your modem or ISP WAN. What is its address?

So by saying it has no default gateway, you shouldn't have Internet right now. Is that the case too?

Open command prompt and type IPCONFIG /ALL. Your gateway should be listed...its usually the first available host address on a network. Example... 192.168.0.1

If your IP Address is 192.168.100.137 odds are your router is 193.168.100.1. That would be your NICs gateway address and what you would type into your web browser to access your router.

You might already know this. But I wanted to cover that much so we can get an idea of where to go from here. Cheers!
Click to expand...

1. I already have a gateway configured in my house, so no, i'm not relying on this router for internet. However, I plan to make this into an access point in the very near future.

2.This is what I'm getting when i follow that step....

Autoconfiguration IPv4 Address. . : 169.254.205.6(Preferred
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :

So with this i tried 169.254.205.1 with unlucky results :/

RCoon · Mar 4, 2021

I cant access to my wifi router

Hello marcosamerio..
If you are unable to connect access your wifi router then there must be some problem with connection. I think the following step scan help you to connect it properly to wireless router.

Connect your computer to the wireless router. Although you can access the router wirelessly, it is better to use an Ethernet cable to directly connect to your router so that you can securely adjust router settings. Plug the Ethernet cable into the appropriate Ethernet jack on your computer. Plug the other end of the cable into any one of the open Ethernet ports on the back of your wireless router.

2. Open a Web browser. In the URL address field, enter the IP address for your wireless router. This information should be contained in your router’s manual. If you cannot find it, enter “198.168.1.1” as the address. This is usually the default IP address for most routers.

3. Enter the username and password for your router. This should also be supplied in the router’s manual. If you don’t have this information, go to the RouterPasswords website and find the brand and model of your router. This site lists the default login information for most wireless routers.

4. You should now be able to see your wireless router settings. You can configure your network ports, as well as SSID (wireless network name) and passwords.
Click to expand...

You have replied twice with no reply from OP and no discernable reason.
Reporting for spam.

Windows 10: Cannot access my router dashboard

Cannot access my router dashboard

Cannot access my router dashboard

Cannot access my router dashboard

Cannot access my router dashboard - Similar Threads - Cannot access router

dashboard

Can’t access my router dashboard.

How to access router

Cannot Access USB Storage on ASUS Router

Cannot access Router IP or NAS IP

Question about accessing my router

Can't access Privacy dashboard

Can't access router.

Spartan browser cannot access my Router