Windows 10: Computer will not now post after Win 10 clean install

I'm not too sure with this kind of thing, but can it have something to do with your CMOS battery? Just brainstorming(sometimes it helps)*Think

 

Let me emphasize that my system appeared 100% stable the few times it booted. I believe I was even able to restart the computer with no problems. All is perfect, except when I shut my computer off completely.

 

But I sent my motherboard to Gigabyte and they say that all is well with it, testing it in multiple configurations.

 

If the motherboard is fine? Then its Power supply, CPU or RAM, assuming it has onboard video. If doesn't add that to the list. Can you put your RAM into another PC to test it? What do you have for spare parts? I would swap power supplies first, if you have a spare. Any beeps coming from the motherboard? The beep code may tell you what's going on.

 

I asked about CMOS because of this article I read once: http://www.utilizewindows.com/pc-fun...d-boot-process

 

I did an RMA on the power supply and it's already on its way. If the problems persist, I talked to a computer expert at my local computer shop and he said he can diagnose the problem. This will probably be my best option if the new PSU does not fix things.

 

Did you delete all your old partitions. I recommend reading How to do a Clean Install in this forum.

 

The motherboard will not POST. It does not get through the Power On Self Test. This has to happen before the hard drive is accessed and the OS is loaded. If the motherboard will not POST you can't do a clean install. *Wink

 

Thanks! I have an old Windows XP computer as a spare. I'm going to be patient and wait until I get my new power supply before I make any more RMAs. If the PSU does not fix things, I think I'm going to have my computer technician diagnose it for me. I spoke to him on the phone and he said that he would do it, and the pricing was not bad the last time I used him.

 

A no POST is one of the hardest things to figure out. Especially if you don't have spare parts to swap in and out. It sucks to have to pay somebody to look at it, but sometimes you have no choice. If it's a quick fix, it shouldn't cost much. It's either RAM, CPU or Motherboard. RAM is a quick swap, that would be what I looked at first. Then CPU. I hope it all works out OK for you.

 

I'm betting that it's the power supply. The manufactures have been very supportive. G.Skill was almost insistent that I mail them my memory as an exchange, but I'm going to wait until I try the new PSU. I personally think that it's relatively rare for the CPU to go bad, especially given the fact that my system was so solid the few times it did post. Same for the memory. It's only 6 months old and I did a long, long test using MemTest86+ when I first installed the ram and everything was fine. For both memory sticks to then flake out at the same time sounds unlikely to me.

Thanks for your time and support!

 

Power supply is usually at the top of my list for situations like this. Motherboard is number two when it was stable, but now won't POST. Bad RAM usually causes other issues as a hint that something is wrong. And it's usually only one stick that goes south.

 

It sounds to me like you have a hardware issue somewhere. Are there any beep codes when it fails to POST?

I would suggest a complete teardown and boot up after each component is installed. Its ok if the system beeps in an expected sequence to tell you there is no ram. In fact that's good.

Have you tried out of case assembly? Assemble the core comps on an ESD safe surface or test bench case and see if it works there?

I once had a system that would fail post, post and not show all the ram, post and show all the ram, post and show portions of the ram and most USB ports were DOA - not responsive. Kind of like rolling the dice each time I powered it up. All of this was due to the fact that my HEATSINK (Noctua) had shipped without four neoprene washers that went on each of the four posts and sat between that back of the motherboard and the heatsink mount plate. I went to home depot and bought four washers for .87¢ and this resolved what had been several weeks of just wacky behavior. This all came about though as a result of a complete teardown and chatting with others on a forum like this one.

Little .87 cent washers were the difference between solid reliable system performance and total instability. Anyway just saying, you just never know what will cause a ground issue and prevent post. But you can eliminate the causes with a solid process of elimination.

*NOTE* that Noctua fan/cooler is still working in that system to this day. It was purchased with the first CORE i7 920 series in 2009(IIRC). Prior to that time I was not familiar with Noctua at all and have since had only good experiences with their products. So just wanted to be clear I was not implying anything negative about Noctua products.

 

I wish my case came with a speaker. Not being able to hear those beeps is a major obstacle in troubleshooting this. I understand that many cases produced today do not have the capacity to beep.

I'm also using a Noctua, which is quiet and easily cools my 65w cpu.

The biggest clue is that my system seems rock solid when it does boot, and that my system was solid for about 9 months since building it. No hardware changes since that time. No overclocking, which is largely responsible for those CPUs that do fail.

 

I keep a couple of speakers I removed from old cases I junked just in case I ever need one. The last couple of cases I bought had a spot for a speaker but no actual speaker installed. Most motherboards these days come with a little speaker mounted right on the motherboard. About all its good for is making a beep sound, I wouldn't even really call it a speaker, more of a little buzzer.