Windows 10: Did the Windows 11 Update Mess Up Your HP Computer?

I first had a problem with my cursor disappearing. I did a chat with someone at Microsoft. Gave access to my computer. He did a few things and was advised to restart after 30 minutes. I followed the instructions, and the cursor returned. Five hours later, the cursor froze. The entire screen froze. I turned off the laptop, and every since then, when trying to restart, it does nothing. I've been in a never-ending boot screen for days!The first message says: Preparing Automatic Repair.The second message says: Your device ran into a problem, and we'll restart it for you.Then, the laptop goes back

:)

 

HP Spectre Folio 13 lost Bluetooth after latest Windows 11 update

After the most recent Windows 11 update, Bluetooth on this HP Spectre Folio 13t-Ak000 CTO stopped working. The computer refuses to report that it has Bluetooth, so no controls are visible. Given the proximity to the Windows 11 update, I am assuming that it is a software conflict rather than a hardware failure. The latest manufacturer's updates are for Windows 10 only.

The following steps were taken, to no avail:

• Airplane mode was turned on and off.
  
• A corrupted device driver, suspected as being the misinterpreted Bluetooth driver, was removed and the computer was rebooted to force a reinstallation.
  
• All Windows and HP updates were installed, including a BIOS update.
  
• System File Checker repaired the OS.
  
• HP's network drivers were downloaded and reinstalled on the system.
  
• The Bluetooth troubleshooter was run but no Bluetooth hardware was detected.
  

I have also posted this report on the HP boards. I have considered looking for the component manufacturer's Bluetooth drivers, if any, but I can't figure out the manufacturer. Any suggestions would be welcome.

 

Unable to access HP Simple Pass to Sign-in to the computer on Windows 10

Hi Jerome,

Thank you for posting in Microsoft Community and being a part of Windows 10.

I understand your concern about accessing HP simple pass after upgrading to Windows 10. We will help you with this issue.

• Do let us know the make and model of your computer?
• Have you installed HP simple pass software on your computer?

Try the below steps and check if it helps.

Step 1: I suggest you to download the latest HP Simple Pass software from the manufacturer's website install it and check if it helps.

Step 2: If you have already installed the software, I suggest you to re-install it and check if the issue persists.

Follow the steps to Access Recovery Manager:

• Press Start button from the keyboard, type Recover Manager.
• Select Recovery Manager from the list when it becomes available. Allow the action to continue, if prompted. The
  HP Recovery Manager opens.
• Click Software program re-installation, Next , select
  HP SimplePass for the listing and then follow the on-screen instructions to reinstall application
  

Hope it helps. Try the above and get back to us with an updated status of this issue for further assistance.

 

HP Printer messed up

Hi,



Thank you for writing to Microsoft Community Forums.



We appreciate the efforts you have taken in trying to resolve this issue. We understand that after an update you are unable to print from your HP printer. However, it would be great if you can help us with the details mentioned below:

• Do you receive any error message/code when you try to print? If yes, what is the error message?
  
• Were you able to install the drivers successfully?
  
• May I know which update was installed on the computer recently? To check go to
  Start >> Settings >> Update & Security >> Windows Update >> View update history.
  

We would suggest you to check if the Printer is listed in Device Manager. Refer the steps mentioned below:

1. Press Windows key + X, and select
   Device Manager.
   
2. Expand Printers and check if the Printer is listed.
   

We would suggest you to run HP Print and Scan Doctor on your computer and see if that helps. The HP Print and Scan Doctor will automatically detect for the issues and diagnose them. You can download the HP Print and Scan Doctor from the
Utility-Diagnostic Tool section in
HP LaserJet Pro M203dw Printer.



For additional information, see
Fix printer connection and printing problems in Windows 10.



As you have mentioned that you are unable to remove the printer from the computer, we would suggest you to follow the steps mentioned below and remove the traces of the printer from the registry, restart the computer and then try installing the drivers.



Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow
these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs.



Refer the article to
Create a system restore point.



Step 1: Restart Print Spooler service

1. Press Windows key + R, type
   services.msc and click on OK.
   
2. Now, look for Print Spooler service, right click on it and select
   Restart.
   

Step 2: Cancel print jobs

1. Search for Print management (PMC) on the search bar in the
   Taskbar and open it.
   
2. Click on Printers, select all the printers (Press
   Ctrl when selecting), right click and select
   Cancel all jobs to delete the pending print jobs.
   
3. If PMC is not available, open printer’s print queue via
   Settings (Windows key + I, Devices) and
   cancel all pending print jobs.
   

Step 3: Remove all third-party printers

1. Press Windows key + R, type
   control printers and click on OK.
   
2. Now, right click on the third party printers and select
   Remove.
   
3. If this doesn’t work, press Windows key + R, type
   regedit and click on OK.
   
4. Navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers
   
5. Under Printers, delete all the third party printers except:
   

• Fax
  
• Microsoft Print to PDF
  
• Microsoft XPS Document Writer
  
• OneNote
  
• Send To OneNote2016
  

Step 4: Remove all third-party drivers

1. Press Windows key + I, to open
   Settings.
   
2. Click on Devices, and select
   Printers & scanners on the left pane.
   
3. Now, click on Print server properties and select the
   Drivers tab.
   
4. Remove all the third party drivers. Do not remove any
   Microsoft print driver.
   

Step 5: Uninstall OEM software

1. Press Windows key + R, type
   appwiz.cpl and click on OK.
   
2. Find and uninstall all the printer related
   OEM software.
   
3. Verify the same from registry by navigating to
   HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitor
   
4. Delete all the third party print monitor from the location except:
   

• Local Port
  
• LPR Port
  
• Microsoft Shared Fax Monitor
  
• Standard TCP/IP Port
  
• USB Monitor
  
• WSD Port
  

Step 6: Set Print Spooler service Startup Type to Automatic

1. Press Windows key + R, type
   services.msc and click on OK.
   
2. Look for Print Spooler service and double click on it.
   
3. Set the Startup Type to Automatic from the drop down.
   
4. Restart the computer
   

Step 7: Re-add the printer

1. Press Windows key + I, to open
   Settings.
   
2. Click on Devices, and select
   Printers & scanners on the left pane.
   
3. Select Add Printer or Scanner to re-add the device.
   

Let us know how it goes.



Regards,

Nikhar Khare

Microsoft Community - Moderator