Windows 10: Drive clone to SSD won't boot to Win 10...

Startup repair didn't fix the issue.

What do you need to see to help me?

I upgraded windows from 7 to 10 on this machine. It boots and runs properly (but slow) on the ST mechanical drive.
After the cloning operation with the ADATA version of Acronis, the SSD will not boot and the boot sequence stops
with a message that "boot device not accessible". Booting from USB. Before I go into the machine to physically install it, I would like to know that it is going to boot.

Laptop is a Compaq Presario CQ57 with AMD E300 1.3 ghz processor and 4GB RAM.

The new SSD is ADATA SU800 256GB

Windows version is Win 10 20H2

Suggestions welcomed.

Thanks in advance!

Not sure I've introduced myself but I'm not new to computers and have worked with quite a number of them. First PC was a Gateway 486dx66 with 4 mb RAM. Cost me as much as a decent used vehicle back then.

EJ

:)

 

Moving to SSD. Clone or not to clone?

Part of how I keep my SSD fast is to clone it to a platter drive, then clone back. You just want to make sure that you are only cloning teh used space, and not the empty space.


So, again, I isntall Windows to the ssd. Clone to platter drive, then clone back.

I am not sure why, but if I do not do the clone step, the drive's speed, and windows booting, decreases substantially within a week or so.

I am using a Corsair F60 SSD and a Western Digital 500AAKS as drives, and using the free version of Acronis that WD provides, if any of that matters. I am not sure, at this point.

 

Unable to boot Windows after cloning it to SSD

Hi,



Thank you for writing to Microsoft Community Forums.



I understand that you are facing issues while booting the PC after cloning Windows to new SSD. I would like to know what happens when you try to boot the PC to desktop using SSD?



The reason you are not able to boot the PC is that the files required to boot Windows are still recognizing the HDD as the main drive. I would suggest you to try rebuilding the BCD files and see if you are able to boot the PC using
SSD.



Kindly follow the steps below to rebuild the BCD.

1. Create a bootable media and boot the PC using the media.
2. On the Install Windows screen, select Next >
   Repair your computer.
3. On the System Recovery Options screen, select
   Troubleshoot> Advanced options > Command Prompt.
4. Now type in the commands and hit enter: BOOTREC /FIXMBR
   
   BOOTREC /FIXBOOT
   
   BOOTREC /scanos
   
   BOOTREC /rebuildbcd
5. Restart the PC.

If the issue persists, please get back to us with the results of the troubleshooting steps to assist you further.



Regards,

Prakhar Khare

Microsoft Community – Moderator

 

boot from cloned ssd installed on cd drive

I have to assume that the cloning software you used made the SSD bootable. You can only confirm that by checking the software's documentation and confirming that you followed the procedure correctly.

I also assume that you have made a system image of the HDD. I also assume that you made a Recovery drive or a System repair disk unless you have an installation disk [which can also do the same job]. You will need this if the cloning has not worked correctly
and you need to restore your system.

The BIOS might not be capable of booting from a SSD/HDD in the CD bay. Whilst that can be a convenient location for doing the cloning, you will almost certainly need to remove the original HDD and fit the SSD
in its bay instead.

Put the old HDD in a USB enclosure so that it can be used as a storage drive but do not connect it to the computer while you are trying to get the SSD to boot. Bootable HDDs & SSDs have "signatures" that the system will look for during booting and finding
multiple signatures will confuse it & probably stop it booting at all.

If, when the SSD has proved itself, you decide to fit the old HDD in the CD bay as an onboard additional storage drive then you will need to format it first so hold off on this until you are completely confident in the SSD.

- - - - - - - - -

When I did this job last year, I used Acronis TI to "clone" to the SSD. Actually, what I did was use Acronis TI to restore a system image to the SSD. That is, in effect, cloning it but I thought that it would be a more reliable way of doing it as TI system
images are tolerant of changed hardware being found.

• I put the SSD in the CD bay to do the image restoration.
• I removed the old HDD and put the SSD in its bay.
• The SSD booted correctly.
• After a while, I reformatted the old HDD and fitted it in the CD bay as an onboard additional storage drive.

Best of luck,

Denis