Windows 10: Error After Installing Android x86.org 0xc0000428

I had experimented.Regrets.I was having a feeling to dual boot android with windows. I went to install android x86 on my Laptop.Specs:Toshiba Portege M930 It's a touchscreenCpu: Intel R Core i5-2450m x64, but OS 32-bitGpu/Igpu: Intel HD Graphics 3000 pretty sure V1Ram: 4GB of ram: 2.7 Gigs available to use.SSD: 128 Gigs o' spaceOS: Originally WIndows 7 32-bit Factory fresh; Upgraded Unofficially to WIndows 10 32-bitExtra: Punched it because of the touchy-touchy driver was lagging: There's a damn crack and one of the sides ain't no workin. Anyways;I went to >>>https://www.andr

:)

 

Dual boot Windows 10 and Android-x86

Hello!


Excuse me if this is the wrong section, please move to the appropriate section. My colleague has an old netbook and would like to either install Android-x86 on it or dual-boot with Windows. As I am a bit more advanced, I decided to try it myself so I can help him step-by-step.


The first attempt was to install Android-x86 only in a USB Flash drive. So I removed my test-notebook's hard disk (to avoid any accidents) and proceeded with the installation. I won't go into details as this is not the purpose of this post. After some attempts I did it right and could boot into Android-x86.



Then I wanted to go a step further and dual-boot with Windows. My Colleague is going to use Windows 7, but I had already installed Windows 10 Pro 32-bit on my test-notebook and wouldn't want to format and install 7. Besides, how different it could be using Windows 10? So I loaded Computer Management, then Disk Manager and shrank the Windows partition by about 10GB to make room for the Android-x86 installation. To identify the space easily within Android-x86 Setup, I even created a new simple volume and formatted it as FAT32 and labeled it Android. Within Android-x86 installation there were no partition names, only sizes in KB, but I managed to identify the correct partition and install Android there. When asked I also installed the Grub boot loader to be able to boot into Android and added an entry for Windows. After reboot I expected to boot into Grub and see selections about Andoid-x86 and Windows. But instead I booted into Windows 10! So I thought to use EasyBCD to add a boot entry for Android. Using the Metro interface made no difference and the computer booted into Windows 10 again without giving me any choice. I then loaded EasyBCD again and this time I disabled the Metro interface, so I had the old good Windows 7 (legacy) boot loader. I could see the entry for Android but I could not boot into that. I tried to add a boot entry with Grub (legacy) connected to the Android partition without any success. Then I tried all other available partitions, naturally nothing again. Once I tried to add a Grub2 entry but all I got was an empty list without boot entries, so I saw a Grub command prompt. I know nothing of Grub, so I cannot use this command prompt to boot into Android-x86.


Is anyone familiar with Grub and EasyBCD to tell me what to do? If that helps, in Windows Disk Manager I see 4 partitions and Android is installed in the third partition which is formatted as ext4. In Android Setup I see more partitions (weird) and the Android partition is sda5. Android-x86 was 6.0 RC1 Marshmallow, but I don't think that matters.



Thank you in advance...

 

Unable to boot the device with error: 0xc0000428 on Windows 10

Hi Vuk,

Thank you for posting in Microsoft Community and being part of Windows 10.

I understand the inconvenience you are facing in booting the device with 0xc0000428 error. We will help you with this issue.

Do let us know the following to assist you better with this issue:

• What is the make and model of your device?
• What is the complete error message along with the error code of this issue?
• From when are you facing this issue?
• Have you make any hardware/ software changes to your device prior to this issue?

I would like to inform that when you attempt to start a Windows 10 system, the system fails to start normally and you receive an error:
0xc0000428 for the signed driver dlkmdldr.sys. Do confirm us if you are facing the same issue.

Try the below and check if it helps.

Step 1: I suggest you to remove all the external devices except mouse and keyboard, hard reboot the device and check if the issue persists.

Step 2: I suggest you to boot the device by choosing the "Disable Driver Signature Enforcement" mode from the advanced boot menu, you would be able to boot the system to the desktop.

• Try to boot the device to Windows Recovery Environment
• Click on Advanced options, Startup Settings
  and Restart.
• Once the computer restarts, press F7 key to start he device on
  Disable Driver Signature Enforcement mode.
• Check if the computer boot successfully.

Step 3: I suggest you to install the pending updates on your device after restarting the computer.

Steps:

• Connect to the internet.
• Press Windows key and type
  updates.
• Click on Check for updates.
• Under Windows Updates, click on
  Check for updates.
• Try to install the updates being shown.

Hope it helps. Try the above an update us the status of this issue to assist you further accordingly.

 

How to install exchange 2016 into exchange 2010 org

i installed 2016 into 2010 exchange org. but im looking for full step by step guide. i need to move roles? publuic folders, certs, etc. i keep seeing instructions on install and i did that and i have it in 2010 org but i know theres a ton of other steps
to complete it. after i comeplete install i need to get rid of 2010 exchange.