Windows 10: HP 15-ba009dx W10 190x & 2004 upgrades fail due to ACPI driver problem

Product: 15-ba009dx

Operating System: Microsoft Windows 10 64-bit


Currently on W10-1803. For most of this year W10 has tried and failed to upgrade to either 1903 or 1909



I have been trying 2004 for a few days but also failed.



Setupdiag logs have identified a multitude of driver issues which I have corrected but I'm now stuck with a failure to update the ACPI driver.



Query-remove: ACPI\PNP0A08\1
! dvi: Query-removal vetoed by 'SCSI\Disk&Ven_&Prod_KINGSTON_SA400S3\4&a0128e0&0&000000' veto type 6: PNP_VetoDevice.
! dvi: Device required reboot: Query remove failed : 0x17: CR_REMOVE_VETOED.
dvi: Query-remove: PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&11
! dvi: Device required reboot: Query remove failed : 0x13: CR_FAILURE.
dvi: Query-remove: PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&14
! dvi: Device required reboot: Query remove failed : 0x13: CR_FAILURE.
dvi: Query-remove: PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&15
! dvi: Device required reboot: Query remove failed : 0x13: CR_FAILURE.
! dvi: Unable to clear marking on device 'ACPI\PNP0A08\1' to allow driver loads again. Error = 0x00000013
! dvi: Unable to clear marking on device 'PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&11' to allow driver loads again. Error = 0x00000013
! dvi: Unable to clear marking on device 'PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&14' to allow driver loads again. Error = 0x00000013
! dvi: Unable to clear marking on device 'PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&15' to allow driver loads again. Error = 0x00000013
dvi: Start: ACPI\PNP0A08\1
dvi: Start: PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&11
dvi: Start: PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&14
dvi: Start: PCI\VEN_1022&DEV_1439&SUBSYS_82F6103C&REV_00\3&2411E6FE&0&15
! dvi: Unable to update reboot required reason. Error = 0x0000000d

:)

 

Brightness problem due to Microsoft ACPI-Compliant Method Battery driver

Hello. I have a Lenovo PC and there is a problem with the brightness. My laptop suddenly goes dim even if the brightness is set high and the battery plan is the bright screen plan. This happens when my laptop is not plugged in.

• When the laptop is plugged in, the brightness problem disappears. On unplugging again, the problem comes back.
• It happens even when the battery level is high.
  
• The problem is temporarily fixed by restarting the laptop. But the issue recurs.
• When I disabled Microsoft ACPI-Compliant Method Battery driver, the brightness is restored. But it returns to the original state when the driver is enabled.

I do need the Microsoft ACPI-Compliant Method Battery driver, but this problem is annoying, especially when my charger is not around and the screen goes
very dim.

Please post a solution for this problem. The same problem was posted by a user with a HP laptop and the solution posted asked the user to check with HP Customer Support. But I feel its a problem with the driver or the power management of Windows.

Thanks in advance.

 

Problem with 2004 IS0

It does help if you read the replies *Wink I mentioned the 4GB Fat32 limit in post #6

As for getting MCT to run on your machines, I showed in post #6 a screenshot of it running on mine.

In post #18 I suggested troubleshooting steps to get the MCT to run, and if that failed a way to split up an install.wim that's larger than 4GB.

 

not able to get drivers for "PCI Simple Communication controller" for Laptop HP 15 r205TU -- SOLVED

Hello All,
I was just facing the same issue and I found one of the blog post with complete step by step instructions, it was mentioned on one of the ecommerce site snapdeal.

A user had posted the link through which he solved the problem and it worked for me as well. here is the URL: http://www.techavin.com/hp-15-r205tu-k8u05pa-drivers-wifi-issue-solved/ hope you guys will find it useful.

Thanks.