Windows 10: I cannot update Windows version 1909 to 20H2 when using the Windows Update Assistant

I cannot seem to get the Windows featured update from 1909 to 20H2. I have tried troubleshooting the Windows update through the settings, but I have had no luck. I have updated all the drivers as well as the BIOS and then tried the Windows update assistant again with no luck. My laptop is only a year old, i7 16GB RAM and have a lot of space on my hard drive for the update. Every time I run the Windows Update Assistant more than half way through the process I get the following prompt:


"This PC can't be upgraded to Windows 10."
"Your PC has hardware that isn't ready for this version of Windows 10. Windows 10 Update will automatically offer you this version of Windows 10 once the issue has been resolved"


If my laptop is not ready for this update, would any one be able to give me a better insight as to when it may be available?

:)

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.

 

Windows Update suddenly hangs?

Windows Update is suddenly hanging for some reason... I went and downloaded and installed the first bunch of updates, restarted when asked, and now when I go back to windows update I just get the window with a white box forever. Reboot and it still does it. This happens to be on my main machine, running windows 7.

I've also noticed when I reboot it says configuring windows update, step 3 of 3, 47%. Maybe it somehow skipped something and is screwed forever?

 

Windows updates...

Oh. Your "Registry" must have gotten screwed up FLY3R. If for some reason you couldn't download your updates I suppose you could go to the update site, and run throught the steps 'till it fails activation. Then you could go up to "Tools > Manage Add ons > then disable "Windows Genuine Advatage Validation Tool." Of course you should only use this method if you are having problems updating your legitamate copy of Windows XP. Perhaps do to a corrupted piece of software? *Smile