Windows 10: Laptop's new Nvme SSD only detected when plugged into power

Recently i bought a new Nvme SSD to install windows 10 on it.I installed the OS and everything worked well, but, if i shutdown it and turn it on without charger it gives me 3f0 hard disk error, and if i turn it on with charger eveerything works.I tried to reinstall it and it gives always the same problem, same as disabling Secure Boot.Any suggestions?

:)

 

Upgrade Windows 7 on SSD NVMe to Windows 10 on SSD NVMe

Hi Varnium,

Thanks for updating me.

Usually, you can install Windows 10 on SSD NVme directly if your computer BIOS detects it.

You can try the following steps if your computer detects the SSD NVme:

1-After creating a Windows 10 bootable USB and going through the installation process. From the Installation page "Install Now", press F10 to open the Command Prompt.

2-Type these commands and hit enter:

diskpart

list disk

select disk X (Replace X with your SSD NVme number shown in the list above)

clean

3-Restart your computer and go through the installation process.

If your computer does not detect it or the BIOS detects it, but you cannot see it during the installation process, it is best to contact your computer manufacturer's support services to provide you with accurate information about configuring BIOS.

Here are similar cases:

https://eu.alienwarearena.com/ucf/show/261122/b...

https://daily.slickdeals.net/tech/how-to-instal...

https://www.dell.com/support/kbdoc/en-ae/000132...

Note: Make sure you can find all Windows 10 compatible drivers for your computer from manufacturer's official website and your computer fully supports Windows 10 before taking further actions.

Please do not hesitate to ask if you need further assistance.

____________________________________________________________

Standard Disclaimer: There are links to non-Microsoft websites. The pages appear to be providing accurate, safe information. Watch out for ads on the sites that may advertise products frequently classified as a PUP (Potentially Unwanted Products). Thoroughly research any product advertised on the sites before you decide to download and install it.

 

Re-installing windows 10 on new NVMe SSD

I am about to upgrade my HP laptop with a NVMe SSD. My laptop came with pre-installed windows 10 Home Single language in HDD.

I want to install windows 10 into NVMe SSD. I like to know the safest process involved to do so. I went trough some website suggesting to use third party software to clone the OS , do some changes in BIOS setting. Can I just make a recovery USB from recovery
drive in windows and then boot the laptop and install OS in NVMe and format the C drive in HDD? OR is there any other way ?

 

Clone present nvme pcie ssd to replacement nvme pcie ssd?

I have a 500GB M.2 2280 NVMe PCIe SSD (boot drive) that I want to replace with a higher capacity M.2 card.

Where do I put the new SSD during the NVMe to NVMe cloning process? My mobo only has one M.2 slot for NVMe SSD's so do I want to use an external adapter for one of the M.2 cards? If so, do you have a recommendation?

If you have solved this issue for your desktop or laptop I would like your advice on if and what extra hardware you needed during the cloning.

please remember that I am dealing with PCIe NVMe drives ONLY. NO Sata is involved except possibly for a connecting cable from the desktop to an adapter. I am experienced with cloning SATA III drives but cloning NVMe is a little
new to me.

Computer: Dell XPS 8920, 32GB ram.

Present SSD: KXG50ZNV512G NVMe Toshiba 512GB

New SSD: CT13049074 Crucial P1 NVMe PCIe M.2 SSD 1TB (or 2TB if available soon) or similar storage device.

Windows 10 Pro for Workstations, version 1809.