Windows 10: Modified Macrium backup

Dell Inspiron 15 5565, Win 10 Home

I want to create a Mactium backup, but it's going to be huge unless I can properly modify it. I tried to use a USB with 28gb free space as the destination, but it wasn't enough





My first question is can I just image the first 4 partitions, leaving out that 12.95gb image partition (recovery drive?), and the Dell support partition, and still restore that Macrium image without a problem?

Secondly, will shrinking that 906gb OS partition make the backup smaller, or will an Intelligent sector copy essentially do the same thing?

And if I shrink that partition, then I'll have enough space to store that image, but I'm a little anxious about doing it because if I mess something up I have no recovery option.

Also, if I can create the Macrium backup, can I delete that recovery partition?

:)

 

Restoring Windows 10 Image using Macrium Reflect


In addition to the above. Here's my suggestion in step by step.
I assume you have Macrium Installed in your current HD and already made a backup copy.

1. Connect your new HD via USB port and boot up.
2. Run Macrium, click on Restore tab then select the Backup Image that you made to restore
3. click on "select a different target disk" then select your new HD as destination
   
   
   
4. Proceed to restore then Shutdown and disconnect the old HD and replace with the new HD
5. Boot up with your new HD.

 

Need Serious Help: How To Record Video of What is Done on my PC?


I suggest the following simple steps:

1. Set the autosave options in MS Office to a low value say 5 minutes.
2. Setup file history to autosave frequently - the shortest period is 5 mins
3. Install Macrium Reflect Free and configure it to do a daily incremental system backup

You should be well covered if you do the above to protect your key files.

 

Backup Issue - Microsoft 10 - Cannot perform initial backup

Question

• 
  
  

Applies to

• Windows
• Windows 10
• Update, backup, & recovery

5 views Backup Issue - Microsoft 10 - Cannot perform initial backup




My backup stubbornly refuses to run. I can't run the initial backup, therefore the file history backups don't run either. This has been an ongoing problem for quite some time. Suggestions I've received have not worked so far. Following is the problem
and the failed resolution attempts:

• I get this message from the Event Log:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID - 201

Level: Error

User - System

*** ---- There is no config file at this directory location. The contents of the location are:

catalog1

catalog2

config1

config2

• In another thread from July, someone suggested checking a particular service (I forget the name just now) is running. It is.

• Two days ago a Microsoft employee suggested the following steps. These steps resulted in no change, still no backup:

KA

Karthicka_R replied on

• Microsoft
• Support Engineer

Hi,

Thank you for contacting Microsoft community.

I suggest you to follow the below steps to start and stop the services “Windows backup” and “volume shadow copy” and check if it helps.

• Press “Windows+R” and in the run command box type “services. MSc”.
• Search for the service “Windows Backup” double click on it and check whether the service is started or not, click on “OK” button. I suggest you to stop and start the service again.
• Once done again search for the service “Volume shadow copy” double click on it and check whether the service is started or not. I suggest you to stop and start the service again, click on “OK” button and
  check whether you can perform backup successfully.

Hope this information was helpful and do let us know if you need further assistance. We will be glad to assist.

• I performed these steps multiple times. The backup still crashes, with the same error message. In addition I collected the following error message, but only one time:

Unable to start a backup cycle for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 200

• Can anyone help me with this stubborn problem?

Thank you in advance.