Windows 10: Shrinking a exciting partition on hard drive safety check

Thank youRead here its not an issue to have to back up everything before I do free up some space .seems with what I've read here I don't need some App for that. I can and Right inside Windows disk management. Right right click on partition format/shrink etc.I need only 15 or 20 MB of allocated space out of the whole 4 partitions on the drive.Appreciation decades of worry free use of your computers laptops etc. Ive not needed anything from the best around nothing ever broke not any real problems They were not Microsoft Nope . Any difficulties were self infected learning the ins and outs o

:)

 

remove external hard drive partitions

Hi,

Thank you for posting your query on Microsoft community.

If you are logged in as an administrator, you can repartition your hard disk by using the Shrink feature in Disk Management. You can shrink an existing partition or volume to create unallocated disk space, from which you can create a new partition
or volume.

You may follow the step below and check if it helps:

• 
  Connect the external hard drive.
  
• 
  Press Windows Key and click on Disk Management.
  
• 
  Right-click the volume you want to shrink, and then click
  Shrink Volume.
  
• 
  Follow the instructions
  

You may also refer to the steps below and check if it helps:



Open cmd with admin rights

1. Run Diskpart application by typing Diskpart

2. In the “Diskpart” prompt, enter rescan command and press Enter key to re-scan all partitions, volumes and drives available.

3. Then type in list disk and press Enter key to show all hard disk drive available.

4. Select the disk that contains the partition you want to remove. Normally, with just 1 hard disk, it will be disk 0. So the command will be:

select disk 0

5. Finish by Enter key.

6. Type list partition and press Enter key to show all available and created partition in the disk selected.

7. Select the partition that wanted to be deleted by using the following command, followed by Enter key:

select partition x

where x is the number recovery partition to be removed and unlocked its space. Be careful with the number of this partition, as wrong number may get data wipes off.

Finally, type in delete partition override and press Enter key.



Disclaimer: Be sure to back up any data you want to keep before you begin.



Hope this helps to resolve your issue. If the problem persist please revert back to us we are glad to help you.

 

hard partition

Hi Prasad,

Thank you for posting in Microsoft Community.

I understand that you are trying to extend the Volume of Drives and create partitions from C: drive.

I would suggest you to follow the steps and check if it helps you.

• Press Windows + R keys, type diskmgmt.msc hit
  enter.
• Disk management will open. Right click on the C: drive
  below in the segments of the partitions.
• Select Shrink Volume. Select the Amount of space
  you want to extend in MBs (1GB = 1024MB).
• Follow the instruction and check if it creates a Unallocated Drive.

Later after the Unallocated drive is created follow the below steps to crate a partition.

• Right click on the Unallocated drive and select
  New Simple Volume.
• Select the Drive letter and follow the instructions and check if it
  creates a partition.
• Follow the same to Create partition.

Note: C: drive must be not less than 100GB if you are using a 1TB hard drive. partitions must not be more than 3 drives to have a better functioning of the system.

Keep us posted to help you better.

 

W7 Hard drive partition issue

to get rid of that 100 meg windows partition that setup creates for you on a new install on a blank hdd:

- press shift+f10 when on the partition management screen in setup <-- this opens a command prompt
- diskpart <-- start the windows command line partition management tool
- list disk <--- list the installed hdds in this computer for the next step
- select disk 0 <- might have to replace 0 with the number of the correct disk
- clean <-- this will erase all data on the disk you selected one step up- dont use the wrong disk!
- create partition primary <- creates a primary partition taking up all space on the drive, adjust the command if necessary
- exit, exit to exit diskpart and the command prompt
- click refresh in partition manager and select your newly created partition and install to that