Windows 10: System 10 backup error.

unable to perform backup on external hard discs due to error code 0x80070013, "the media is write protected".?

:)

 

system image backup, 807800c5 error


@injaneb, thanks you put me on the right track! In my case there were 2 extra steps:

1. The extra EFI was not on the C disk but on the J disk (the target of the backup) which was an external USB. I don't know why an EFI was made there. To remove that EFI partition, follow these instructions [1] carefully. I needed only the instructions using the built-in diskpart tool. Just make sure you selected the right disk!
2. Before redoing the backup, delete the files on J: (the target disk) that were created by the previous botched backup. Their existence would cause exactly the same error code to show up.

[1] What is EFI System Partition | How to Delete EFI System Partition - EaseUS

 

Backup Issue - Microsoft 10 - Cannot perform initial backup

Question

• 
  
  

Applies to

• Windows
• Windows 10
• Update, backup, & recovery

5 views Backup Issue - Microsoft 10 - Cannot perform initial backup




My backup stubbornly refuses to run. I can't run the initial backup, therefore the file history backups don't run either. This has been an ongoing problem for quite some time. Suggestions I've received have not worked so far. Following is the problem
and the failed resolution attempts:

• I get this message from the Event Log:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID - 201

Level: Error

User - System

*** ---- There is no config file at this directory location. The contents of the location are:

catalog1

catalog2

config1

config2

• In another thread from July, someone suggested checking a particular service (I forget the name just now) is running. It is.

• Two days ago a Microsoft employee suggested the following steps. These steps resulted in no change, still no backup:

KA

Karthicka_R replied on

• Microsoft
• Support Engineer

Hi,

Thank you for contacting Microsoft community.

I suggest you to follow the below steps to start and stop the services “Windows backup” and “volume shadow copy” and check if it helps.

• Press “Windows+R” and in the run command box type “services. MSc”.
• Search for the service “Windows Backup” double click on it and check whether the service is started or not, click on “OK” button. I suggest you to stop and start the service again.
• Once done again search for the service “Volume shadow copy” double click on it and check whether the service is started or not. I suggest you to stop and start the service again, click on “OK” button and
  check whether you can perform backup successfully.

Hope this information was helpful and do let us know if you need further assistance. We will be glad to assist.

• I performed these steps multiple times. The backup still crashes, with the same error message. In addition I collected the following error message, but only one time:

Unable to start a backup cycle for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 200

• Can anyone help me with this stubborn problem?

Thank you in advance.

 

Backup Issue - Microsoft 10 - Get Backup Errors - Third Try Didn't Work

This is my third try for help.

I've enclosed my problem, the steps suggested which I performed, and current status.

My backup stubbornly refuses to run. I can't run the initial backup, therefore the file history backups don't run either. This has been an ongoing problem for quite some time. Suggestions I've received have not worked so far. Following is the problem
and the failed resolution attempts:

• I get this message from the Event Log:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID - 201

Level: Error

User - System

*** ---- There is no config file at this directory location. The contents of the location are:

catalog1

catalog2

config1

config2

• In another thread from July, someone suggested checking a particular service (I forget the name just now) is running. It is.

• Two days ago a Microsoft employee suggested the following steps. These steps resulted in no change, still no backup:

KA

Karthicka_R replied on

• Microsoft
• Support Engineer

Hi,

Thank you for contacting Microsoft community.

I suggest you to follow the below steps to start and stop the services “Windows backup” and “volume shadow copy” and check if it helps.

• Press “Windows+R” and in the run command box type “services. MSc”.
• Search for the service “Windows Backup” double click on it and check whether the service is started or not, click on “OK” button. I suggest you to stop and start the service again.
• Once done again search for the service “Volume shadow copy” double click on it and check whether the service is started or not. I suggest you to stop and start the service again, click on “OK” button and
  check whether you can perform backup successfully.

Hope this information was helpful and do let us know if you need further assistance. We will be glad to assist.

• I performed these steps multiple times. The backup still crashes, with the same error message. In addition I collected the following error message, but only one time:

Unable to start a backup cycle for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 200

• Can anyone help me with this stubborn problem?

Thank you in advance.

You had this question

• 
  
  
  
  

• All replies (1)

DM

Divya M replied on

• Microsoft
• Support Engineer

Hi,

Thank you for posting your query on Microsoft Community.

We sincerely regret for the inconvenience caused.



Method 1Perform a Clean Boot to see if there is any software conflict as clean boot helps in eliminating software conflicts.



Note: After performing the troubleshooting steps in clean boot, follow Step 7 from the link to return the computer toNormal startup mode.



Method 2: Run check disk to check for any errors.



Note: If any bad sectors are found in the hard drive then it might try to repair that particular sector. If you have any data on that, it might be lost.

You may also follow the below link and check if it helps:

http://windows.microsoft.com/en-us/windows/preview-backup-restore



Please let us know if you need further assistance.



Thank you.

-----------------------------------

Yes, I need more assistance.

I ran a disk check on both the source and destination drives for the backup. No errors.

I executed a clean boot. (I have left myself in the clean boot). It doesn't seem to work

I'm not sure to check whether it has worked, and I just couldn't tell. How do I confirm that the initial, image, backup has been completed?

The event viewer reports this error every time I attempt to manually initiate a backup:

Unable to scan user libraries for changes and perform backup of modified files for configuration C:\Users\Papa\AppData\Local\Microsoft\Windows\FileHistory\Configuration\Config

Event ID: 201.

I'm assuming that with this error, my backups are not being done.