Windows 10: Teredo

I've tried everything to get this stupid Teredo thing to work. I've looked in legacy hardware, it's not there, I've changed the client type, doesn't work, set it to default, doesn't work, updated drivers, doesn't work, clicked 'fix it' doesn't work'.


I'm at a complete an utter loss, everything was fine a few days ago?

:)

 

Can You Please fix the teredo adapter problem already?

Hi Mr Overshield,

Teredo being disabled is one of the possible reasons why you're unable to fix the Teredo problem as well as can't find it under hidden devices. To re-enable your Teredo on your device, I suggest that you follow the steps below:

1. Type in cmd in to the search bar on your desktop and right click on Command Prompt and run it as admin.
   
2. Type in netsh interface Teredo set state type=default
3. Kindly restart your computer to let the changes take effect.

Note: No need to reinstall the Teredo as it will install itself.

For additional information and troubleshooting steps, you may visit the link below:

Click here

Kindly update us with the results, so that we can assist you further.

 

Teredo Tunneling not on computer.

Hi,

Your concern about Teredo Tunneling can be due to the configuration of the device. We'd recommend performing the following commands to fix your concern:

• Search Command Prompt using Cortana.
• Right-click on Command Prompt.
• Select Run as administrator.
• Type the following in order:
  • netsh, press Enter.
    
  • int ipv6, press Enter.
    
  • set teredo client, press Enter.
    
  • Check if the item is already posted.
  Note: If the above steps did not suffice, proceed to the next step.
  
• 
  Search and launch Device Manager using Cortana.
  
• 
  Search and locate LogMeIn (Hamichi) if it's listed. If yes, proceed to the next step.
  
• 
  Right-click on the specified driver, and then select Properties.
  
• 
  Click on the Driver tab.
  
• 
  Locate and click on the Disable button.
  
• 
  Check if Teredo Tunneling is already posted.
  

In the event that the above steps didn't work, we'd recommend posting the query in our TechNet forums. The community consists of IT Professionals that would be able to impart their knowledge in relation to your concern. To reach the site, click on this

link.

Note: We'd also recommend to check this thread from time to time as there might be a community member either existing or new that may be able to share their expertise with Teredo Tunneling.

Let us know should you need further assistance.

 

Teredo unable to qualify

Hi JayKay,

Thank you for writing to Microsoft Community Forums.

Failure to obtain a Teredo IP address can occur when there’s an issue with your Teredo adapter, when a device on your network is blocking the Teredo protocol, or if there’s software installed on your PC that’s disabling
Teredo functionality. If you haven’t tried the methods listed in the following articles yet, I would suggest you to try them first and see if it works:

• Teredo is unable to qualify
  
• Xbox app server connectivity on Windows 10 is blocked
  
  

Note:

Serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry
if a problem occurs. To backup and restore registry key, refer to this
link.

If the issue persists, I would suggest you to
uninstall and re-install the Xbox app to see if you can get it to work.

• Right click the Windows icon on the taskbar and choose Windows PowerShell (Admin).
• Copy and paste the following command and hit Enter:
  
  Get-AppxPackage Microsoft.XboxApp | Remove-AppxPackage
• Reboot the computer once the command is executed.
• Once the machine restarts, launch Microsoft Store and reinstall the Xbox app.

After reinstalling the Xbox app, open Windows PowerShell (Admin)
again and copy paste the following command to enable Teredo.

netsh interface Teredo set state type=default

Let us know how it goes.

Regards,