Windows 10: the user profile service service failed the sign-in & Blinking blank screen at taskbar in...

Hello all,Recently I reset my laptop after that while I am trying to login it is showing the user profile service service failed the sign-in because of that I thought it is better to enter into safe boot mode but it was taking so long and after that it is showing blinking blank screen in safe boot mode. I can't do anything in safe mode so I tried to open task manager using Ctrl+alt+delete it worked and then I restart windows explorer but issue didn't resolve. After that I checked value of winlogon shell value is explorer.exe or not but it is explorer.exe. After that Using run new task of task

:)

 

The User Profile Service service failed the sign-in. User profile cannot be loaded.

Hello,

When attempting to login to my computer, I get the following message:

"The User Profile Service service failed the sign-in.

User profile cannot be loaded."

I referred to this Help article,You receive a "The User Profile Service failed the logon” error
message,

but the only difference is I only have one user profile on this computer. So, I can't login with another user to go through the steps listed in this post.

Any suggestions?

Thanks,

 

The User Profile Service service failed the sign-in

Hi there,

I have an Asus Prime Z270-A motherboard, I had an M.2 SSD connected to the M.2_2 slot and a HDD connected to SATA6G_1 slot.

The SSD contained Windows OS and was my C: drive and the HDD contained my Users data and was D: drive.

I installed a new M.2 SSD into the additional M.2_1 slot running in SATA mode.

When I booted into Windows my profile picture wasn't there and I received the message:

"
The User Profile Service service failed the sign-in

User profile cannot be loaded.
"

Which at first I found was because the SATA slot SATA6G_1 gets disabled when using my SSD arrangement. I disconnected the new SSD and all worked fine again. I moved the HDD to a different SATA connection and installed the new SSD, but I got the same problem. This time when disconnecting the the new SSD the error continued.

When I go into windows repair and command prompt, run diskpart it had mixed my drive letters up, which I guessed would be the issue as it is no longer finding the User files in D: ?

I reassigned the drive letters in diskpart but when booting into windows they must reassign themselves as going back into diskpart shows them incorrect again.

I have also tried re-assigning drive letters in AOMEI Partition Assistant, but same happens.

I figured my only option would be to load regedit and change the path for my User files?

Before doing this I looked on the internet to try some solutions, for one of them I ran:

bootrec /fixmbr
bootrec /fixboot
bootrec /scanos
bootrec /rebuildbcd

I think fixmbr ran but the others said couldn't find windows installations.

Please remember my computer still boots into windows (log in screen) but just can't find users profile location.

Back in diskpart I couldn't set any of the partitions on my SSD to active, so looking on the internet it mentioned about partitions being hidden, I had one hidden Volume 1 (ESP) so I ran attrib clear hidden. Since doing these I don't seem to be able to get all my troubleshooting options from holding shift when clicking the power button on the log in screen now. So I have to boot from a Windows USB to get to this now...

I followed a guide for bootrec - attrib C:\bootbcd -h -r -s but get the message C:\boot not found.

I've been going round in circles.

AOMEI Partition Assistant actually shows some of the partitions as boot, but doesn't show my SSD as MBR it's GPT. Not sure if this is a problem as again it still loads windows...

If anyone has any suggestions it would be greatly appreciate, in command prompt browsing directories on both drives, everything seems to be there. So I'm hoping it's still just the drive letters resetting themselves. I've attached photos of some of the screens.

Thank you in advance.

 

User Profile Service Service failed


Hello Manjunath, and welcome to Ten Forums.

See if you may be able to use OPTION FOUR in the tutorial below to enable the built-in Administrator account at boot.

https://www.tenforums.com/tutorials/2...a.html#option4

If so, then sign in to the built-in Administrator account to be able to do the steps in the tutorial below for this error.

User Profile Service failed the sign-in - Fix in Windows 8