Windows 10: Unable to start my Pc

Discus and support Unable to start my Pc in Windows 10 BSOD Crashes and Debugging to solve the problem; I am unable to start my pc. It is Dell Inspiron 3420. It just shows me windows icon and then, pc stops. It has been occuring since I have restarted my... Discussion in 'Windows 10 BSOD Crashes and Debugging' started by Parth Dipendra Maheshwari, Nov 1, 2020.

  1. Unable to start my Pc


    I am unable to start my pc. It is Dell Inspiron 3420. It just shows me windows icon and then, pc stops. It has been occuring since I have restarted my computer for updates. It went till 30% and then it went off. Since then it is not starting. I have run the diagnostics. Hardwares are fine

    Please help. Its urgent

    :)
     
    Parth Dipendra Maheshwari, Nov 1, 2020
    #1

  2. PC unable to start

    Hello,

    thanks for your reply.

    I have tried step 2nd but it didn't start any automatic repair window.

    please suggest.

    thanks.
     
    Umesh_Joshi, Nov 1, 2020
    #2
  3. PC Build Steps

    Ok just because I like steps i am going to create some steps. Please give me the stamp of approval/disapproval
    • Install system in case
      • Remember to connect SSD and optical to same SATA ports on motherboard
    • Turn on PC
    • setup HDD
    • run blend test in prime95 for 30-60 min
      • run realtemp at the same time
    • While in Prime95 test
      • if CPU goes above 70c in RealTemp, I have a leaky CPU
      • if my system locks up or blue screens, there is an instability in the system somewhere
      • if my system does not lock up or blue screen, my CPU is not damaged and I am in the clear!
    What do you guys think??
     
    anandsap123, Nov 1, 2020
    #3
  4. Unable to start my Pc

    Sometimes unable to log in

    Hi,



    To troubleshoot you concern, we recommend you to start your computer in safe mode, then perform clean boot after. Refer to the links below for steps:


    After performing a clean boot, follow the steps under the section How to reset the computer to start normally after a clean boot troubleshooting.

    If the suggestions above will not work, you can follow the troubleshooting steps found on this

    link
    .



    Regarding your pin concern, we suggest you to refer to Jessen P's
    suggestions on April 25, 2015 found on this
    link
    .

    Update us on the result.



    Thank you.
     
    Angela Pun, Nov 1, 2020
    #4
Thema:

Unable to start my Pc

Loading...
  1. Unable to start my Pc - Similar Threads - Unable start

  2. Unable to start Windows Defender Advanced Threat Protection Service

    in Windows 10 News
    Unable to start Windows Defender Advanced Threat Protection Service: [ATTACH]The Windows Defender Advanced Threat Protection service is a critical security component in Windows. When this service fails to start, your system becomes vulnerable to advanced threats and malware, as real-time protection and monitoring are disabled. You may have...
  3. unable to start Windows Admin Centre Service on Windows Server 2025 Azure vm.

    in Windows 10 Gaming
    unable to start Windows Admin Centre Service on Windows Server 2025 Azure vm.: Hello Experts,I am facing issue while connecting Windows Admin Centre for a vm via Azure portal. Steps i followed:1 Open the specific vm windowpane in Azure portal.2 Select 'Windows Admin Centre' from left pane3 Check mark both boxes for Network rules to be created4 Select...
  4. unable to start Windows Admin Centre Service on Windows Server 2025 Azure vm.

    in Windows 10 Software and Apps
    unable to start Windows Admin Centre Service on Windows Server 2025 Azure vm.: Hello Experts,I am facing issue while connecting Windows Admin Centre for a vm via Azure portal. Steps i followed:1 Open the specific vm windowpane in Azure portal.2 Select 'Windows Admin Centre' from left pane3 Check mark both boxes for Network rules to be created4 Select...
  5. Unable to start the Driver

    in Windows 10 Gaming
    Unable to start the Driver: Hi Team,I am encountering a problem with a driver signed using the "Microsoft Windows Component Preproduction CA 2024" certificate. When attempting to start the service, I receive the following error message:[SC] StartService FAILED 2148204812: A certificate was explicitly...
  6. Unable to start the Driver

    in Windows 10 Software and Apps
    Unable to start the Driver: Hi Team,I am encountering a problem with a driver signed using the "Microsoft Windows Component Preproduction CA 2024" certificate. When attempting to start the service, I receive the following error message:[SC] StartService FAILED 2148204812: A certificate was explicitly...
  7. Random Blue Screen of death has left my computer unable to start

    in Windows 10 Gaming
    Random Blue Screen of death has left my computer unable to start: Hey everyone, my computer randomly blue screened yesterday and I have been stuck in a boot loop ever since. I have tired a bunch of different things, and to be honest I don't remember all of them, but some of them resulted in me eventually getting stuck with boot error...
  8. Random Blue Screen of death has left my computer unable to start

    in Windows 10 Software and Apps
    Random Blue Screen of death has left my computer unable to start: Hey everyone, my computer randomly blue screened yesterday and I have been stuck in a boot loop ever since. I have tired a bunch of different things, and to be honest I don't remember all of them, but some of them resulted in me eventually getting stuck with boot error...
  9. Unable to start a DCOM Server

    in Windows 10 Gaming
    Unable to start a DCOM Server: Whenever I try to connect to an OMRON PLC via USB I get the following error appear in Event Viewer and I'm unable to connect to my PLC. I have two other devices that can connect without issue. I've tried completely removing and reinstalling the OMRON software so it doesn't...
  10. Unable to start a DCOM Server

    in Windows 10 Software and Apps
    Unable to start a DCOM Server: Whenever I try to connect to an OMRON PLC via USB I get the following error appear in Event Viewer and I'm unable to connect to my PLC. I have two other devices that can connect without issue. I've tried completely removing and reinstalling the OMRON software so it doesn't...