Windows 10: USB drive showing up as 2 Drives on PC [Fix]

​

Some Windows users have complained that when they connect a USB drive to their Windows PC, the USB drive shows up as 2 different drives when they plug it in. If you are facing the same issue, we have you covered with all working fixes. So, check out below. Fix USB drive showing up as […]

This article USB drive showing up as 2 Drives on PC [Fix] first appeared on TheWindowsClub.com.

read more...

 

help. USB drive isn't assigned a drive letter.

Any usb flash drive I plug into my computer isn't assigned a drive letter. The physical drive shows in the "safely remove hardware" but it doesnt show up in disk management. I have tried to populate the volume thru the safely remove hardware properties window and it does pop up in the list but it doesn't stay there. This isn't a format or assign a letter problem. It's more complicated then that. Maybe one of the services needed for usb drive management was disabled? Suggestions needed. btw external usb harddrives work fine.

 

My USB Backup drive does not show in My Computer window.

Hi Meran,

A few possible reason can cause your external drive to not show in File Explorer. To diagnose and fix this issue, we suggest that you check the Disk Management window. To open it, follow the steps below:

• Right-click on the Start button.
• Select Disk Management.
• Alternatively, you can search diskmgmt.msc in Cortana.

Examine the list of drives in the Disk Management window and look for your external drive. Even if it doesn’t show up in File Explorer, it should appear here. If the drive appears, it may not be appearing in File Explorer because it needs to be assigned
a drive letter. To do this, right-click the partition on the drive in Disk Management and select
Change Drive Letter and Paths.

If you don’t see the drive in the Disk Management window at all, we suggest that you try connecting the drive to a different USB port or use a different USB cable. We also recommend that you avoid using USB hubs, and connect the drive directly to your computer.

If you need further assistance, please do not hesitate to post a reply.

 

Recovery Drive for Windows 10 Doesn't Recognize USB Drive

When I try to create a Recovery Drive in Windows 10, Windows doesn't recognize the flash drive.

I'm following the instructions to create a Recovery Drive listed here:

Create a recovery drive - Microsoft Support

• 
  From the taskbar, search for Create a recovery drive and then select it. You might be asked to enter an admin password or confirm your choice. (I was asked to confirm my choice, and I clicked "Yes".)
  
• 
  When the tool opens, make sure Back up system files to the recovery drive is selected and then select
  Next.
  
• 
  (Secret Step) Wait a minute or so for the "Please Wait" screen to finish thinking
  
• 
  Connect a USB drive to your PC, select it ...
  

The issue is that when I connect a USB drive to the PC, it doesn't appear on the "Connect a USB flash drive" screen as a drive that can be selected, and the "Next" button is grayed out.

However, when I look in File Explorer, I can see the USB drive plugged into the computer. Selecting Properties shows that Windows considers its Type to be "Removable Disk". (Sounds right to me.)

I'm not getting any error messages.

My environment:

A brand new Toshiba Sattelite C55-C5241 laptop with Windows 10 Home. It's never had anything other than Windows 10 on it - unless they upgraded it at the factory.

A brand new ativa 8GB USB flash drive. Note that the packaging for the USB drive does not include Windows 10 in the System Requirements, but seriously?

What I've tried:

• Plugging the flash drive into all three USB ports (USB 2, USB 2, and USB 3)
• Reformatting the flash drive with FAT32
• Restarting the computer with the flash drive plugged in
• Turning off Real-Time Scanning in McAffee

I've seen a few threads with this issue in Windows 8, but none of the potential solutions in those threads have worked for me. So here I am asking the same question, but for Windows 10.

Does anyone have any suggestions for resolving this issue?

Thank you.