Windows 10: Wifi adapter keep disabling by itself until now

It's been a couple weeks I've been strugling with this, while im playing on my asus tuf A15 FX506II laptop the connection suddenly disconnect by itself. When i check device manager, my wifi network adapter which Realtek 8822CE Wireless LAN 802.11ac PCI-E NIC was disabled by itself and i have to wait for a couple minutes for it to reenabled by itself because i cant enable it by myself and sometime it even worse, i have to restart my laptop for thousand times to make it right. And it's even worse when i tried to play valorant, my wifi network adapter is gone after i play it for a couple m

:)

 

WiFi adapter disables itself

Sorry, but that does not solve the problem. Here's the condition, any suggestions?

Asus and HP laptops upgraded to Win 10 August 2015, both using anniversary edition version 1607, 64 bit, installed on 8-24-16. All of the fixes suggest have been tried and do not work. A/V is Norton Security.

• WiFi adapter disables itself and will not allow it to be re-enabled. Troubleshoot will not fix and restart is required.
  But Restart hangs and takes 30+ min. (90 min. 1-8) to complete or a forced shutdown by physically turning off the PC is needed to resolve.
  Can cause Edge to fail to find web pages after restart.
  • Asus last occurred: 12-25-16, 12-14, numerous dates since August 2015.
    Happened occasionally while on Win 8.1
  • HP last occurred: 1-8, 1-6, 1-1, 12-27-16, 12-14, numerous dates since August 2015. Never happened while on Win 7.

 

How to permanently disable ms virtual wifi adapter

Hi,

You may permanently disable the Virtual Network Adapter and Virtual Wifi Adapter by deleting it completely from the Network and Sharing Center.

To do this, kindly follow the steps below:

• Press Windows key + X on your keyboard.
• Select Control Panel.
• Click Network and Internet.
• On the left-side, click Change adapter settings.
• Right click on the name of the adapter, then choose Delete.

Let us know how it goes.

 

Problems when sharing WiFi with the Virtual Adapter

For many years I have always shared Internet to my devices like phone and tablet with my PC's WiFi antenna through the Microsoft Wi-Fi Direct Virtual Adapter, I only use it for that, since I have a cable connection, and I start the wifi with the command NETSH WLAN start hostednetwork previously having done the settings of NETSH WLAN set hostednetwork mode=allow ssid="Wifi" key="password".

For my devices to connect it is necessary that the Virtual Adapter that is created with that command has access to the Internet, for this I have to share the Internet from my Ethernet adapter to the Virtual Wifi adapter.

For some time now (a couple of months) I've been experiencing problems when sharing the Internet through that medium. The problem is that when I start the WiFi my devices do not connect, they say "Getting IP address" and never connect.

I have found the solution and I have to do the following:

1. Disable the Virtual Adapter with the command netsh wlan stop hostednetwork.
2. Remove the connection sharing from the Ethernet Adapter.
3. Activate the Virtual Adapter with the command netsh wlan start hostednetwork.
4. Adding connection sharing from the Ethernet Adapter to the Virtual Adapter again.

By doing these steps my devices can now be connected to the Wifi, but sometimes it doesn't work if I do these steps too quickly. I have noticed that if I do step 3 and 4 too quickly it does not work and I have to repeat the process but doing these last two steps more slowly, until the Virtual Adapter gets an IP address 192.168.137.1 from Internet Protocol version 4

Also this problem does not occur 100% of the time. Sometimes when I run the command to start the Wifi everything happens fine and my devices connect well but this only works after my PC has been on for at least 5 minutes (I haven't counted it). If I run the command as soon as my PC has turned on then it doesn't work anymore.

As I mentioned before this problem didn't occur before because I had configured a .bat file that ran as soon as the PC was turned on with the NETSH WLAN start hostednetwork command and everything worked fine.

Now, I would like to go back to before when everything was fine so that when my PC starts up the WiFi too and I don't have to do all this protocol all the time, but with a simple command everything is solved.

Could someone give me a hand with this?