Windows 10: Windows 10 1809 update fails. How to change a regkey while the update is in progress?

Hi there,

I have a machine that keeps failing on the Windows 10 1809 upgrade. It's currently at 1803.


And I think I know what the problem is.


During the 1803 upgrade the Intel RST driver was changed by the upgrade. This causes the machine to take about 30 minutes to boot up. I discovered that changing a related reg key, see below, gets the system boots back to a very quick couple of seconds.


I suspect that the 1809 upgrade is also changing that RST driver again, resetting that regkey to the default value that causes the 30 minute bootup. But this time the upgrade is noticing the long boot time. It assumes there is a problem, and reverts back to 1803 before it boots into Windows.


Then after a few days of weeks it tries to force the 1809 upgrade again. Rinse and repeat.


So what I need is to be able to either prevent the 1809 upgrade from changing that key or the Intel RST driver, the ability to change that key back to what I had it set at before it tries booting, or find a way to increase the time-out variable so that it will boot into Windows instead of giving up and reverting back to 1803.


The reg key change that should fix this is: [HKEY_LOCAL_MACHINE\System\ControlSet001\Enum\PCI\VEN_8086&DEV_2822&SUBSYS_B0001458&REV_00\3&13c0b0c5&0&FA\Device Parameters\Interrupt Management\MessageSignaledInterruptProperties]

"MessageNumberLimit" from decimal "80" to "1".

:)

 

Windows Updates failed to instal

I just did step one and they have just all installed.... thank you so much.... it was quite frustrating having that update window pop up every 5 minutes and failing to instal every time

Thanks mate

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.

 

Windows 10 Update

Well just noticed a pretty large one pop up coming in at 914MB, seems it makes some pretty serous updates.

KB3172985
https://support.microsoft.com/en-us/kb/3172985

This security update includes improvements and fixes in the functionality of Windows 10 Version 1511 and Windows Server 2016 Technical Preview 4. It also resolves the following vulnerabilities in Windows:

• 3175677 MS16-094: Security update for secure boot: July 12, 2016
• 3174060 MS16-093: Security update for Adobe Flash Player: July 12, 2016
• 3171910 MS16-092: Security update for Windows Kernel: July 12, 2016
• 3170048 MS16-091: Security update for .Net Framework: July 12, 2016
• 3171481 MS16-090: Security update for Kernel Mode Drivers: July 12, 2016
• 3170050 MS16-089: Security update for Windows secure kernel mode: July 12, 2016
• 3170005 MS16-087: Security update for the Microsoft Print Spooler: July 12, 2016
• 3169999 MS16-085: Cumulative security update for Microsoft Edge: July 12, 2016
• 3169991 MS16-084: Cumulative security update for Internet Explorer: July 12, 2016