Windows 10: Windows 10 update 1809 /1903 fails to install

0x8007042b (this is for 1809)

Yes I have tried all ways to get this to install and it will not install, clean boot, ren software distribution, sfc, dism, latest stack, everthing! recommended and will not install. No third party antivirus. This is pretty annoying.


OS Name Microsoft Windows 10 Home

Version 10.0.17134 Build 17134

Other OS Description Not Available

OS Manufacturer Microsoft Corporation

System Name IM19UDV

System Manufacturer ASUSTeK COMPUTER INC.

System Model G20AJ

System Type x64-based PC

System SKU All

Processor Intel(R) Core(TM) i7-4790 CPU @ 3.60GHz, 3601 Mhz, 4 Core(s), 8 Logical Processor(s)

BIOS Version/Date American Megatrends Inc. 0703, 2015-04-29

SMBIOS Version 2.8

Embedded Controller Version 255.255

BIOS Mode UEFI

BaseBoard Manufacturer ASUSTeK COMPUTER INC.

BaseBoard Model Not Available

BaseBoard Name Base Board

Platform Role Desktop

Secure Boot State On

PCR7 Configuration Binding Not Possible

Windows Directory C:\WINDOWS

System Directory C:\WINDOWS\system32

Boot Device \Device\HarddiskVolume2

Locale Canada

Hardware Abstraction Layer Version = "10.0.17134.858"

User Name IM19UDV\mstar

Time Zone Eastern Standard Time

Installed Physical Memory (RAM) 8.00 GB

Total Physical Memory 7.94 GB

Available Physical Memory 5.05 GB

Total Virtual Memory 9.19 GB

Available Virtual Memory 5.94 GB

Page File Space 1.25 GB

Page File C:\pagefile.sys

Kernel DMA Protection Off

Virtualization-based security Not enabled

Device Encryption Support Reasons for failed automatic device encryption: TPM is not usable, PCR7 binding is not supported, Hardware Security Test Interface failed and device is not InstantGo, Un-allowed DMA capable bus/device(s) detected, TPM is not usable

Hyper-V - VM Monitor Mode Extensions Yes

Hyper-V - Second Level Address Translation Extensions Yes

Hyper-V - Virtualization Enabled in Firmware No

Hyper-V - Data Execution Protection Yes

:)

 

Windows Updates failed to instal

I just did step one and they have just all installed.... thank you so much.... it was quite frustrating having that update window pop up every 5 minutes and failing to instal every time

Thanks mate

 

Windows Updates failed to instal

I'm not sure how differant XP media center Edition is but you could clear the history \ cache if these folders are there.

Step 1 Register DLL files.

=================

By trying this step, we can check if the update engines are working properly.



1. Close all instances of Internet Explorer.

2. Click Start and Run, type "Regsvr32 atl.dll" (without quotes) in the Open box and click OK.



Note: There is a space between regsvr32 and atl.dll



3. Similarly, one by one, register the files listed below:



Regsvr32 msxml3.dll

Regsvr32 wuapi.dll

Regsvr32 wuaueng.dll

Regsvr32 wuaueng1.dll

Regsvr32 wups2.dll

Regsvr32 wucltui.dll

Regsvr32 wups.dll

Regsvr32 wuweb.dll

Regsvr32 qmgr.dll

Regsvr32 qmgrprxy.dll

Regsvr32 jscript.dll



Note: If you encounter errors while registering any of these files then skip that file and continue with the next one.



If the issue persists, let's move on to the steps below to verify Windows Update services and temporary folders.



Step 2 Verify the relevant Windows Update services.

=========================================

1. Click Start->Run, type "services.msc" (without quotation marks) in the open box and click OK.

2. Double click the service "Automatic Updates".

3. Click on the Log On tab, please ensure the option "Local System account" is selected and the option "Allow service to interact with desktop" is unchecked.

4. Check if this service has been enabled on the listed Hardware Profile. If not, please click the Enable button to enable it.

5. Click on the tab "General "; make sure the "Startup Type" is "Automatic" or "Manual". Then please click the button "Stop" under "Service Status" to stop the service.

6. Then please click the button "Start" under "Service Status" to start the service.

7. Please repeat the above steps with the other services:



Background Intelligent Transfer Service

Event Log

Remote Procedure Call (RPC)



Note: Event log service is enabled on all of the hardware profiles; this service does not have an option to enable or disable on certain hardware profile.



If it still does not help, let's proceed to step 3.



Step 3 Reload the Update temporary folders.

===================================

One possible cause is that the temporary folder for Windows Update is containing corrupted files. Let's erase all the files there to get the system clean.



1. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net stop WuAuServ



2. Click Start, Run, type: %windir% and press Enter.

3. In the opened folder, rename the folder SoftwareDistribution to Sdold.

4. Click Start, Run, type: cmd and press Enter. Please run the following command in the opened window.



Net start WuAuServ



Please test the Windows Update website and let me know the result. If the issue persists, to clarify the issue and provide more accurate troubleshooting steps, please assist me in collecting the following information.

 

Windows 10 pro 1809 to 1903 update fails

yes it is the upgrade from 1809 to 1903 so its the 1903 that fails.

Yes i did try the The Update Assistant, same error.

If I upgrade using the Media Creation Tool will all my installed programs stay

or will I need to reinstall everything again like with a fresh windows install?